For GM engine pumps. Used with 17360 series.

Neoprene. 10 blades. Diameter: 1-9/16".

Nitrile. 10 blades. Diameter: 1-9/16".

Replacement bearing for Jabsco pumps.

Same pump used in Jabsco multi-engine oil change system Can change oil in a typical V-8 in minutes 3/8" NPT male threaded Dimensions: 7-1/8"L x 3-3/4"W

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

Operates by the rotary sliding vane principle Has vectra rotor and vanes that are designed to handle oil or diesel fuel transfer Pumps up to 5-1/2 GPM and transfers diesel fuel from a 55 gallon drum in 10 minutes Self-priming to 3 feet - Low amp draw Vane Puppies are equipped with a high torque motor with ball type shaft bearings Rated for continuous duty operation Bronze pump has ports with 1/2" internal pump thread 1" external hose barb Also supplied are port adaptors for 3/4" gallon hose thread. Weight: 6.4 lbs

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Quick-release strainer allows for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 53S.
2000 GPH.

Replacement cam liner for impeller pumps. Used with Jabsco 17360 model.

Replacement bearing for Jabsco pumps.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1B Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 14.75 lbs

Three per bag.

Strains debris and particles from bilge pump line. Clear plastic housing for easy inspection. Easy to disassemble and clean. 16 mesh stainless steel screen. 3/4" hose barb ports.

High impact plastic construction. Will not rust, corrode or discolor. Designed for use with Rule pumps. Size: 3/4".

Keeps debris from entering your pump. Plug-in Quad port. Threaded bowl makes cleaning easy. 40 mesh, stainless steel screen. 3/4" hose barb.

Cam screws for Jabsco pumps. Pack of three.

Reducing hose adapter. 1" to 1-1/2".

Replaces Jabsco 30648-1000 "standard format" clips. For Flojet and Jabsco pumps. Two per package.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
12 volt DC.

Engine Cooling Pump & General Purpose Pumping 3.7 GPM, 1/4" NIPT Port Connections. Pedestal mount, corrosion resistant bronze pumps: Use for engine cooling, washdown, circulation, & general purposes on-board or dockside. Bronze or stainless steel shaft installed with permanently lubricated ball bearings for long life & heavy-duty service. Self-priming with ability to operate in either direction at variable speeds. Capacity ranges from 3 GPM to 83 GPM with varied port configurations and sizes. Most models have replaceable cams/wearplates for extended product life. Removable end cover for easy impeller service. Standard impeller for these pump models is neoprene. (some have alternative oil resistant nitrile impellers available.)

Toilet base assembly for Jabsco toilets. Includes all needed installation hardware.

Three per bag.

Solenoid for vented loop (29015). For use with electric toilets. Must be wired in parallel with toilet motor.

A flexible impeller pump. Vertically oriented ports. Mechanical face seal, double row ball bearings. Neoprene impeller. 1" NPT. Overall dimensions: 7" X 4-1/4" X 4".

Cam screws for Jabsco pumps. Pack of three.

Plastic pump body. Designed to provide constant water pressure. 3/8" ports. Automatic flow from tank to faucet. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 13A.
3700 GPH.
Includes a five-year warranty from Xylem.

8 blades. Dimensions: 2-1/2" X 2". Shaft diameter: 5/8".

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27DA.
1100 GPH.

Designed for washdown or for livewell tanks.
Heavy-duty construction.
Ideal for commercial or pleasure boats.
1-1/2" inlet, 1-1/2" discharge outlet.
Rated for 3700 GPH.
Must be mounted below waterline.
Operates at low pressure; not self-priming.
24 volts DC.

Jabsco 50900 Fish Box evacuation pump. A single-diaphragm, 5 GPM plastic-body pump. Perfect for emptying the fisbox after a day's fishing. This self-priming pump is designed to pass debris, such as bait residue, ice particles, fish scales, etc. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Equipped with a one-way duckbill valve. For use in bilge pump installations. Prevents water siphoning from thru hull. Diameter: 1-1/8".

Valve Inlet Non-return 3/4" Fits in pumps suction hose to aid priming & prevent backflow.

Inline Check Valve 1-1/2" Fits in pumps suction hose to aid priming & prevent backflow.

Inline Check Valve 1" Fits in pumps suction hose to aid priming & prevent backflow.