Nitrile. F3. 6 blades. Diameter: 2.56". For Johnson pumps.

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 3/4".
Color: White.
50 feet per carton.

Self-priming, very easy to clean.
Will not rust or corrode.
Length: 36".
1-3/4" diameter.
13 GPM pump rate.
Does not include a outlet hose.

Hayward tank valve head O-ring.

Triangular flange base. Features a field-reversible handle. Handle has a square hole to accept a standard ratchet. Stainless steel handle and hardware. 1" NPT top.

Shields 400/402 Vinylvent Vent Hose 4" 4 1/8" 10 White Venting of bilge gases & fumes. PVC hose supported by helical wire. Resistant to ozone, sunlight and weathering. Will not support a flame.

Flexible impeller self priming bronze pedestal pump.
Typical Marine Applications:
-Engine cooling
-Bilge pump
-Wash-down pump
-Emptying holding tanks  
Bronze body. 3/8" NPT ports.  Rated for 6 GPM at 1800 RPM.  Neoprene impeller. 3/8" stainless steel shaft.
Caution: Do not run dry.

Stainless steel.
Diameter: 2-1/2".

High-pressure cut off switch.

Pump with neoprene impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Nitrile. 6 blades. Diameter: 1-9/16".

Plastic pump body. Nitrile valves and diaphragm. Rated for 8.1 gallons per minute. 1-1/2" ports. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 10-6UL.
2000 GPH.
Has 6-foot wire leads for easy installation.

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1/2".

Replacement volute for "S" Pacer pump. Diameter: 3".

Fuel/water filter canister. Not for use with diesel systems. Weight: .5 lb.

Fuel filter, 5/16" - 3/8". A universal in-line filter. Clear body for quick visual inspections. Protects fuel systems from pollutants. Fits fuel lines from 1/4" to 3/8" ID. NOT for use on inboard engines. Weight: .3 lb.

Knitted-nylon reinforcement.
Tough, weather-resistant vinyl cover.
Excellent handling, even in cold weather.
Solid brass full flow couplings.
5/8" diameter.
100 feet long.

Fuel filter and water separator kit Includes: - Reusable filter head - Water separating fuel filter - 3/8 hose barbs and plugs. Corrosion resistant. For gasoline engines only, NOT diesel. Flow: 20 liters per minute @ 60 psi. Weight: 1 lb.

Thirsty-Mate high capacity super pump. Coast Guard approved for commercial use. Model 519CG#2. Three strokes per gallon, rated for 22 gallons per minute. Inlet hose is 24", outlet hose is 72". Length: 24". Diameter: 3". Weight: 8.3 lbs.

PVC hose with a flexible vinyl helix. Very flexible, abrasion, salt and chemical resistant. Used for bilge pump discharge and drains. Size: 3/4".

Heavy-duty bilge pump. Liquid-cooled, 12-pole motor with double ball bearings. Stainless steel and strong plastic construction. Operates at 120 l/min, 1900 GPH. 4.5 amps, 6 amp fuze. 1-1/8" and 1-1/4" connectors.

U-bolt style exhaust clamp. 
Secures exhaust tubing. 
Diameter: 4-1/2".

Used with standard 10" filter housings (#4-6 10230).

Part number #4-6 15029.

Tohatsu/Nissan fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Tohatsu/Nissan fuel tank connector - male Chrome brass construction. Size: 1/4" NPT. Weight: .1 lb.

Tohatsu/Nissan fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Tohatsu/Nissan tank connector - male. Chrome brass construction. Size: 1/4" NPT. Weight: .1 lb.

Suzuki fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Suzuki/Honda fuel line connector - male. Chrome brass construction. Size: 1/4". Weight: .1 lb.

Honda fuel tank connector - female. Steel / plastic two-prong clip style construction. Size: 3/8". Weight: .1 lb.

Mercury fuel line assembly. Comes complete with primer bulb and fittings. Fuel line is 7 feet long. Surpasses CARB requirements. Size: 3/8" hose barb. Weight: .1 lb.

Honda fuel tank connector - male. Brass construction. Size: 1/4". Weight: .1 lb.

Mercury fuel tank connector - male. Prong clip style tank fitting. Brass construction. Size: 1/4" NPT. Weight: .1 lb.