Allows a user to manually steer an auxiliary engine
(kicker motor) using their existing SeaStar hydraulic
steering system.
Incorporates a 40 series Xtreme cable as linkage between
the two engines.
Allows independent trim/tilt and full steering stroke
of both engines.
Works with SeaStar HC5345, HC5358, HC5348, HC5345-3,
HC5358-3, & HC5348-3 steering cylinders.
Not for use with Baystar steering systems.
Simplified installation, using universal connections.
Maximum auxiliary engine horsepower: 20HP
Cable length: 44".

#6 male SAE to #4 female SAE. 
Brass.

SeaStar 3/8" OD nylon tubing is
recommended for inboard, sterndrive,
and SeaDrive steering systems with SeaStar
(1.7 cubic inch/rev displacement) helms only.
Length: 50'

SeaStar 3/8" OD nylon tubing is
recommended for inboard, sterndrive,
and SeaDrive steering systems with SeaStar
(1.7 cubic inch/rev displacement) helms only.
Length: 25'

For use with Marol power steering pump. Includes mounting hardware.

For use with SeaStar single cylinder outboard system. Length: 27-1/2". Includes instructions.

For pivot mount cylinders. No adapters are required.

Custom adapter plate for Honda Outboard motors.
Used with Marol outboard cylinders

Replacement pulley for Marol steering pump.

For MRB75 / 80.

This kit is designed to mount the helm
at a 20 degree angle to the mounting surface.
For raised or recessed mounts, four possible
mounting configurations are available.
Horizontal recessed mount requires HA5408 drain kit.
Not for use with BayStar helm pumps.

Required for converting a SyTen steering cylinder to a current SeaStar Steering cylinder.

For Teleflex installation purposes. Includes O-rings.

18" SeaStar cylinder hose kit.
Used to connect 3/8" diameter copper tubing to SeaStar steering cylinders.
Adapters and compression nuts included.

Fitting kit for 2nd station/autopilot to inboard or sterndrive applications.
This kit is used with systems plumbed with 3/8" diameter nylon or copper tube only.

Fitting kit to add a 2nd station or autopilot to an outboard steering system.
To be used when the system has been plumbed with SeaStar outboard steering hose only.
Includes non-vented fill plug for lower station helm.

3/8” compression X 1/4" MNPT straight adapter fitting.
Three per package. 

3/8" compression union.
Three per pack.

Elbow. 1/4" X 3/8". Three per package.

1/4” MNPT X 3/8” compression X 3/8" compression tee.
Three per package.

3/8" X 3/8" X 3/8". Three per package.

3/8" compression X 1/4" MNPT X 3/8" compression tee.
Three per package.

Female #6 SAE 45° swivel X 5/16" ID hose.
Brass construction.                      
Field attachable.                        
Fits MSH-5 hose.  

Vertical bleed tee.
#5MORB X 3/8" compression x bleed nipple.  
Two per package.

Horizontal bleed tee.
#5MORB X 3/8” compression x bleed nipple.
Two per package.

90˚ elbow.
#5MORB X 3/8” compression.  
Two per package. 

Straight adapter.  
3/8" compression X #5MORB.
Two per package.

3/8" OD semi-rigid black nylon tubing.
For Hynautic steering control systems.
High tensile strength and excellent coupling
retention in high pressure, temperature and
vibration environments.
Sold by the foot.

Replacement ball joint. Includes washer and nut.

Replacement ball joint. Includes washer and nut.

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 10'

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 12'

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 16'

This kit is used to service many BayStar and SeaStar helms.
Includes:
- Quad ring seal
- Woodruff key
- 5/8" nut
- A top plate
- 3 screws
- Detailed instructions for servicing a SeaStar helm.

For hydraulic control systems. Diameter: 1/4".

Rear-mounted gauge. Displays 0 - 60 PSI.