Nitrile. 8 blades. Diameter: 2-9/16".

Neoprene. 6 blades. Diameter: 2-9/16".

For 18940 series pumps. Includes impeller, O-ring, seal.

Inflates a four-man dinghy in 1-2 minutes. Supplied with an adaptor for all major boats. Reversible, will deflate dinghies flat. Single-handed operation. Rated for 550 liters / minute.

Nitrile. 6 blades. Diameter: 2".

"Flat tank" design makes it easy to change your engine oil. Compact, strong and easy to store when not in use. Equipped with a self-priming, run-dry pump. 3.5 gallon capacity. Includes: - Tank with easy-pour spout - 12 volt diaphragm pump - Dipstick-style suction tube - Battery clamp wire leads.

Clear plastic housing for quick inspection. Keeps debris and particles from clogging pump. Diameter: 3/4".

Repair kit for Jabsco rotor vane pumps. Includes rotor, vanes, O-ring, seal, slinger.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
24 volt DC.

Jabsco 50880 shower drain / bilge pump. A single-diaphragm, 4.2 GPM plastic-body pump. Flexible installation, compact and simple design. Dry-running capability. Pump heads and ports may be rotated during installation. 12 volt.

Replacement bearing for Jabsco pumps.

Two per package. Fits a 36900 series Jabsco pump.

Replacement bearing for Jabsco pumps.

Nitrile. 9 blades. Diameter: 2".

High-capacity, low-profile inline strainer unit. Uses 3/4" ID hose. Transparent housing for easy inspection and cleaning. Fits directly into a diaphragm pump inlet port.

A snap-in port kit for a simple garden hose / pump connection.
Threaded to fit a garden hose end.
Will snap directly into the ports of a Jabsco or Flojet washdown pump.
Two fittings per kit.

For GM engine pumps. Used with 17360 series.

Neoprene. 10 blades. Diameter: 1-9/16".

Nitrile. 10 blades. Diameter: 1-9/16".

Replacement bearing for Jabsco pumps.

Same pump used in Jabsco multi-engine oil change system Can change oil in a typical V-8 in minutes 3/8" NPT male threaded Dimensions: 7-1/8"L x 3-3/4"W

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

Operates by the rotary sliding vane principle Has vectra rotor and vanes that are designed to handle oil or diesel fuel transfer Pumps up to 5-1/2 GPM and transfers diesel fuel from a 55 gallon drum in 10 minutes Self-priming to 3 feet - Low amp draw Vane Puppies are equipped with a high torque motor with ball type shaft bearings Rated for continuous duty operation Bronze pump has ports with 1/2" internal pump thread 1" external hose barb Also supplied are port adaptors for 3/4" gallon hose thread. Weight: 6.4 lbs

Replacement cam liner for impeller pumps. Used with Jabsco 17360 model.

Replacement bearing for Jabsco pumps.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1B Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 14.75 lbs

Three per bag.

Strains debris and particles from bilge pump line. Clear plastic housing for easy inspection. Easy to disassemble and clean. 16 mesh stainless steel screen. 3/4" hose barb ports.

High impact plastic construction. Will not rust, corrode or discolor. Designed for use with Rule pumps. Size: 3/4".

Keeps debris from entering your pump. Plug-in Quad port. Threaded bowl makes cleaning easy. 40 mesh, stainless steel screen. 3/4" hose barb.

Cam screws for Jabsco pumps. Pack of three.

Reducing hose adapter. 1" to 1-1/2".