An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/8" discharge outlet.
Model number: 03.
1500 GPH.

Dockside general purpose pumping and some onboard uses.
Self-priming and portable, very versatile.
Removable end cover allows for easy impeller servicing.
Bronze construction.
For Jabsco model 6050 pump.

Side-mount bracket for Rule pumps. Designed to be attached to a bulkhead, stringer or transom. Works with round pumps from 360 to 1100 GPH.

Plastic adapter. Straight. Diameter: 1-1/2" to 1-1/8".

High impact plastic will not rust, corrode or discolor Specially designed for Rule pumps 1-1/8" straight plastic Weight: .25 lb

Rule oxgenator spray head / aerator. Sprays streams of water into tanks, increasing oxygen. Head is fully adjustable to increase/decrease water flow. For use with 3/4" (19mm) hose. Weight: .25 lb.

Strainer Livewell 3/4" NPS Stainless Steel Livewell Pump Debris Strainer Strainer Livewell 3/4" NPS SS Attach directly to any pick-up tubes on Rule Livewell Pumps. Filters out trash & debris that could clog pump. Stainless steel wire mesh, 3/4" female NPS threads.

90 degree rigid pipe adapter. For 1" NPT.

90 degree rigid pipe adapter. For 1-1/2"- 1-1/4" NPT

High impact plastic construction. Will not rust, corrode or discolor. Designed for use with Rule pumps. Size: 1-1/2".

Motor and pump for a Jabsco 37010 toilet.

Connects to marine engine oil dipstick tubes. Fits threaded male garden hose fitting. Unique design allows one hand pumping. Includes: - Pump with 3/4" brass fitting - Drain hose, 1/2" X 2' length.

For 37010 series heads. 4 blades.

For Jabsco toilets. Used with Jabsco 37010, 37045, 37245. Diameter: 1".

Baked enamel seat and cover. 
Flexible impeller macerator flush pump - fully encased. 
Designed for marine use, above or below waterline. 
12 volt.

Similar in design to an electromagnetic clutch pump. Equipped with a mechanically activated clutch. Provides added operational security in case of power failure Rated for 26 gallons per minute. 1" port.

For use with Jabsco self-priming electric drill pump. Dimensions: 1-9/16" X34".". Shaft diameter: 1/4". Shaft length: 2".

For use with Jabsco 37010.

Jabsco toilet switch. Works with 29090, 37045, 37010 series and other toilets.

Cam screws for Jabsco pumps. Pack of three.

For 34600 series pump. Includes belt, diaphragm, and valve set.

Replaces Jabsco 30648-1000 "standard format" clips. For Flojet and Jabsco pumps. Two per package.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
12 volt DC.

Engine Cooling Pump & General Purpose Pumping 3.7 GPM, 1/4" NIPT Port Connections. Pedestal mount, corrosion resistant bronze pumps: Use for engine cooling, washdown, circulation, & general purposes on-board or dockside. Bronze or stainless steel shaft installed with permanently lubricated ball bearings for long life & heavy-duty service. Self-priming with ability to operate in either direction at variable speeds. Capacity ranges from 3 GPM to 83 GPM with varied port configurations and sizes. Most models have replaceable cams/wearplates for extended product life. Removable end cover for easy impeller service. Standard impeller for these pump models is neoprene. (some have alternative oil resistant nitrile impellers available.)

Toilet base assembly for Jabsco toilets. Includes all needed installation hardware.

Three per bag.

Solenoid for vented loop (29015). For use with electric toilets. Must be wired in parallel with toilet motor.

A flexible impeller pump. Vertically oriented ports. Mechanical face seal, double row ball bearings. Neoprene impeller. 1" NPT. Overall dimensions: 7" X 4-1/4" X 4".

Plastic pump body. Designed to provide constant water pressure. 3/8" ports. Automatic flow from tank to faucet. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 13A.
3700 GPH.
Includes a five-year warranty from Xylem.

8 blades. Dimensions: 2-1/2" X 2". Shaft diameter: 5/8".

Designed for washdown or for livewell tanks.
Heavy-duty construction.
Ideal for commercial or pleasure boats.
1-1/2" inlet, 1-1/2" discharge outlet.
Rated for 3700 GPH.
Must be mounted below waterline.
Operates at low pressure; not self-priming.
24 volts DC.

Jabsco 50900 Fish Box evacuation pump. A single-diaphragm, 5 GPM plastic-body pump. Perfect for emptying the fisbox after a day's fishing. This self-priming pump is designed to pass debris, such as bait residue, ice particles, fish scales, etc. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Equipped with a one-way duckbill valve. For use in bilge pump installations. Prevents water siphoning from thru hull. Diameter: 1-1/8".