Easily converts a gas grill from using small disposable bottles to a larger, refillable cylinder.
Fully assembled and leak tested.
Great for boats, camping, picnics, and more.
Equipped with a hand-wheel POL cylinder fitting on one end, and a high-pressure appliance valve fitting on the other.
Length: 6 feet.

Wall mount.
Two-stage.
Two 300 PSI gauges.
UL listed; meets ABYC standard.

Easily converts a gas grill or other portable LP gas appliance from using small disposable bottles to a larger, refillable cylinder.
Fully assembled and leak tested.
Great for boats, camping, picnics, and more.
Equipped with a hand-wheel POL cylinder fitting on one end, and a high-pressure appliance valve fitting on the other.
Length: 12 feet.

Solid brass swivel fittings.
One side is 1" 20 female for a tee connection; other side is 1" 20 male with O-ring and check valve for an appliance connection.
This hose will connect with gas grill adapter tees.
Fully assembled and leak tested.
Length: 12 feet.

Solid brass high-pressure "T" fitting.
For installation between cylinder valve and regulator or pigtail POL fittings.
Fully assembled and leak-tested.
Swivel male POL to female POl receptacle to 1" 20 male fitting with O-ring and check valve (with captive safety cap).
Designed to be used with a gas conversion hose.
Dimensions: 2" X 4.5" X 2".

Solid brass swivel fittings.
One side is 1" 20 female for a tee connection; other side is 1" 20 male with O-ring and check valve for an appliance connection.
This hose will connect with gas grill adapter tees.
Fully assembled and leak tested.
Length: 6 feet.

Turns LP gas system ON or OFF from installed position.
Has green and red indicator lights.
CE certified gas control panel.
(No detection capabilities; may not be upgraded for LP gas detection.)
12 volts DC.
Dimensions: 2" X 4.5" X 2”.

Used with LP gas detector unit and panel.
Simple to install.
Length: 10 feet.

High-strength fiberglass composite.
Type 1 valve.
OPD, DOT and TC approved.
See-thru feature for level of LP gas.
LP gas capacity: 4.2 gallons.
1260 cubic inch volume.

300 PSI gauge.
20" QCC pigtail hose included.
Wall mount, single stage.
Meets ABYC standard.

Designed to remain constantly ON and monitoring, even when other parts of the LP gas system are off.
Will send an alarm signal to LP gas detection panel when LP gas is present at 10% LEL (Lower Explosion Limit) or more.
Marine UL listed.
Connects with a quick-connect cable (1300-7721-120; 1300-7721-240) to LP gas panels (1300-7760; 1300-7761-KIT).
Dimensions: 2" X 3.5" X 0.75".

High pressure LPG hose with solid brass.
3/8" female swivel flare fittings on each end.
Many people prefer to use hose over copper supply line tubing in their LP gas installations, because it won't corrode, or develop stress fatigue cracks.
Fully assembled and leak tested.
Length: 30 feet.
UL listed.

High pressure LPG hose with solid brass.
3/8" female swivel flare fittings on each end.
Many people prefer to use hose over copper supply line tubing in their LP gas installations, because it won't corrode, or develop stress fatigue cracks.
Fully assembled and leak tested.
Length: 25 feet.
UL listed.

High pressure LPG hose with solid brass.
3/8" female swivel flare fittings on each end.
Many people prefer to use hose over copper supply line tubing in their LP gas installations, because it won't corrode, or develop stress fatigue cracks.
Fully assembled and leak tested.
Length: 20 feet.
UL listed.

Connects to regulator port with hex nipple (included).
Connects to supply hose via outlet port with 90º flare elbow (included).
Will not function at high pressure or with low / no electric current.
Brass construction.

Propane / liquid petroleum gas (LPG) supply hose. Thermoplastic construction. Both ends are 3/8" female flare fittings. Length: 15 feet.

High pressure LPG hose with solid brass.
3/8" female swivel flare fittings on each end.
Many people prefer to use hose over copper supply line tubing in their LP gas installations, because it won't corrode, or develop stress fatigue cracks.
Fully assembled and leak tested.
Length: 10 feet.
UL listed.

Designed to connect wall-mounted regulators
to LPG gas cylinders with Type I valves.
One end has a 1/4" male inverted flare fitting.
Other end has a thermoplastic QCC nut for quick and easy hand tight connection.
The "new-style" QCC connection will not allow any gas to flow through unless properly connected, and has a heat-sensing fail-safe feature that shuts off all gas flow if the the temperature reaches 2400° to 3000° F. Additionally, a controlled-flow device will activate in the case of a downstream gas system break (activates at 200 cubic feet / hour).
Fully assembled, leak-tested, and UL listed.
Length: 20".

5 feet long.
High-pressure rated.
3/8" female swivel flare end fittings.
UL 21 listed.

Brass construction.
Connects a supply hose to outlet with 90º flare elbow.
Regulator outlet port connects with a reducing hex nipple.
Designed to not function with high pressure, or low/no electric current.
Draws 790 milliamp at 12 volt DC.
Dimensions: 2.5" X 1.5" X 1.35".

Designed to connect a tank to a wall mount regulator.
High-pressure rated.
Male POL to 1/4" inverted flare.
Length: 20".
UL listed.

A very compact low-pressure regulator.
Comes fully assembled and leak-tested.
Consists of a solid brass male POL cylinder fitting and street tee; a low-profile, watertight, stainless steel gauge; and a UL listed die-cast zinc body, with a 3/8" FPT outlet.
Designed to be tank-mounted.
Single port, single stage.
Gauge is rated for up to 300 PSI.
Meets ABYC marine standards (LPG System Leak Test 1).
Dimensions: 2.13" X 4.5" X 1.63".