Replacement impeller for "S" model Pacer pump.
3".

Specifically designed for the Pacer S-series pump.
Polyester material, corrosion, rust and chemical resistant.
2" threaded inlet and outlet.

Motor mounting bracket for "S" series Pacer pump.

Replacement volute for "S" Pacer pump. Diameter: 3".

Replacement O-ring for a Pacer "S" series pump.

Replacement body for "S" pump. Diameter: 3".

Hand operated drum pump, for fuel oil, includes pump, suction tube, 8 feet discharge hose & bung adapter, approximately 28 ounces per pump cycle.
A double-acting piston pump.
Chemically resistant.
All internal metal parts in contact with the liquid are made of stainless steel.
N-Gasket: Cork/nitrile.
Discharge hose: 8' EPDM with polyester elbow and nozzle.
Suction tube: 2 piece 1" polyester, 34" long with Teflon tape
1" suction, 3/4" discharge.

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.
Pedestal mount.

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
This model is equipped with a hydraulic motor.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 3" FNPT.

Stainless steel housing and polyester internal parts. Dual 1-1/2" female and 2" male suction and discharge ports. Rated for 3450 RPM.

Pacer self-priming centrifugal electric water pump.
Lightweight, chemically-resistant for general service.
Can handle water, saltwater, waste water, mild acids and bases.
Diameter: 2".
Rated for 110 gallons per minute (GPM) maximum flow.
Glass reinforced polyester with lined volute.
Stainless steel internal parts.

For use with all "I" Pacer pumps.
Includes a Buna-N fitted shaft seal, check valve, and all O-rings needed for an overhaul.

Replacement part / repair kit.
Includes seals and parts needed for a repair job.

For use with "S" series Pacer pumps.
5 vane impeller.

For use with 2" Pacer pump. Housing part, does not include impeller.

For S pump. Ceramic shaft seal.

Upper fill plug.
For use with Pacer pumps.

Replacement lower drain plug.
For S series pumps.

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
This model is equipped with a hydraulic motor.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.