With 4mm power tapping plate. Features increased stainless steel stud length. Clear polycarbonate cover for insulation and protection. Double studs feature "snap out" insulating partition. Size: 8mm. Dimensions: 1.9" x 1.9" x 2.4".

Closed back design completely insulates power from the mounting surface Each screw pair is 1 isolated circuit Jumpers allow creation of common circuits Weight: .1 lb

With 4mm power tapping plate. Features increased stainless steel stud length. Clear polycarbonate cover for insulation and protection. Size: 8mm. Dimensions: 1.9" x 1.9" x 2.4".

With 4mm power tapping plate. Features increased stainless steel stud length. Clear polycarbonate cover for insulation and protection. Size: 10mm (3/8"). Dimensions: 1.9" x 1.9" x 2.4".

316 stainless steel. Locking waterproof cap. Rear safety enclosure with strain relief. 50 amp, 125 volt.

With 4mm power tapping plate. Features increased stainless steel stud length. Clear polycarbonate cover for insulation and protection. Double studs have "snap out" insulating partition. Size: 10mm and 8mm. Dimensions: 1.9" x 1.9" x 2.4".

Safety duplex cable, 12/2 AWG. Manufactured from tinned copper for corrosion prevention. Covered with an anti-abrasive, easily-removed outer jacket. Resists cold, salt water, UV rays, and many petrochemicals. Color-coded red and yellow inner conductor wire. Length: 100 feet per spool.

For electrical system labeling. Blank, black label for custom installations.

Three pole, four wire dockside receptacle. Corrosion resistant, marine-grade construction. Black nylon. 50 amp, 125 / 250 volt

Kit includes: AFI waterproof wiper motor (part number 35500). 6-3/4" - 10-1/2" deluxe adjustable stainless steel arm. 11" Deluxe stainless steel curved blade (33004).

Kit includes:
- 500 waterproof wiper motor
- 11.5" deluxe stainless steel curved blade
- Deluxe adjustable stainless steel arm (6.75" to 10.5").
Windshield mount: .5" shaft diameter.

Hook and catch style classic straight wiper blade. Stainless steel construction. Replaces most standard blades on boats built prior to 1990. Not designed for use with Standard or Deluxe arms. Size: 11".

AC current transformer, rated for 300A AC / 50mA AC.
Diameter: 2.68".

Rugged, insulated copper wire. Meets USCG standards. Resists water, acid, oil, UV radiation. 16 AWG. Color: Brown. Roll of 100 ft.

Markable heat shrink. Easily written upon, gives permanent identification. Tube dimensions: 1/4" X 3". 10 per pack. Weight: .02 lb

250 ampere L-series solenoid switch.
Hermetically sealed contacts.
Activated by optional remote ON/OFF #8230 switch.   
Coil control circuit minimizes heating and amperage draw.  
Nominal voltage: 12/24V DC.
Cranking rating 30 seconds: 1,000A.
Intermittent rating 5 minutes: 400A.
Continuous rating: 250A.
Terminal stud size: 5/16".
IP67 rating: protected against immersion up to 1 meter for 30 minutes.
Dimension: 3.17" wide x 2.63" high x 2.86" deep.

Designed for small spaces and the marine environment. Easily connects with other busbars and fuseholders. High temp plastic and clear polycarbonate construction. 4x 6mm (1/4") studs. 10 x 4mm (5/32") terminals. 200A maximum per bar. Dimensions: 3.9" x 1.9" x 2.0".

Ancor primary wire, 16 AWG. Manufactured from tinned copper for corrosion prevention. Insulated with a flexible proprietary vinyl coating. Resists cold, salt water, UV rays, and many petrochemicals. Color: Dark Blue. Length: 500 feet.

Replacement inlet interior for Marinco standard non-metallic inlets manufactured prior to 1/1/91.  
30A 125V.

For systems with twin engines and two battery banks. House loads can be switched between port and starboard. May be used to parallel the batteries in both positions. Dimensions: 8.2" X 2.7" X 3".

Double pole marine circuit breaker. Provides reliable automatic circuit protection. Designed to ignore nuisance trips. Contructed with marine grade stainless steel springs and specially plated sub-components. Provides over 10,000 switching cycles. Rated for 20 amps. Weight: .17 lb

Designed with extra squeegee "claws" that spread pressure evenly over the length of the blade,
so it will conform to a curved windshield.
All stainless steel and marine-grade silicone construction.

Length: 14".

Bracket for under dash mounting of the Marinco SeaLink® & ConnectPro® receptacles.
Receptacle installs with rear mounting threaded nut.  
Marine grade anodized aluminum.
Dimensions: 2" wide x 2-1/2" high.

Comes with all hot, neutral, and safety ground buses pre-wired and installed.
All circuit labels are backlit (no kit required).
"ON" indicator LED lights for all circuit positions, too.
Rated for a maximum of 100 amps.

Overall dimensions: 3.75" X 10.5".