Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 1-1/4".

Kink resistant and flexible. Designed with an EPDM tube and cover. Wire-reinforced with two fabric plies. Resistant to toilet chemicals, odors, salt water and heat. Primarily used for toilet to holding tank connections. Works well as a holding tank pump-out hose. Diameter: 1".

Deigned for outboard feed and vent lines. Remains flexible at low temperatures. Not for use in Type B1 applications. Diameter: 5/8".

Allows a user to manually steer an auxiliary engine
(kicker motor) using their existing SeaStar hydraulic
steering system.
Incorporates a 40 series Xtreme cable as linkage between
the two engines.
Allows independent trim/tilt and full steering stroke
of both engines.
Works with SeaStar HC5345, HC5358, HC5348, HC5345-3,
HC5358-3, & HC5348-3 steering cylinders.
Not for use with Baystar steering systems.
Simplified installation, using universal connections.
Maximum auxiliary engine horsepower: 20HP
Cable length: 44".

Clear PVC with a black vinyl helix. Abrasion, saltwater, and chemical resistant, flexible. Often used for: - Bilge pump discharge - Potable water tanks fills - Drains for sinks, showers, livewells, or scuppers. This hose uses 147 right hand thread cuffs. Do not attach to thru hull fitting below the water line. Not for use with glycol-based antifreeze. Diameter: 1".

Heavy-duty for hot or cold water systems. Extra wall thickness increases kink resistance. FDA-approved virgin vinyl compound. Diameter: 1/2".

For use with a docking light.

33LU cable with Tee knob. Easy to install and operate. For remote control of choke, throttle, or other engine appli Solid stainless core in a non-metallic liner. Cable can be shortened to needed dimensions. Size: 30 feet. Weight: 4 lbs.

33LU cable with Tee knob.
Easy to install and operate.
For remote control of choke, throttle or other applications.
Solid stainless core in a non-metallic liner.
Cable can be shortened to needed dimensions.
Size: 25 feet.

33LU cable with Tee knob.
Easy to install and operate.
For remote control of choke, throttle or other applications.
Solid stainless core in a non-metallic liner.
Cable can be shortened to needed dimensions.
Size: 20 feet.

33LU cable with Tee knob.
Easy to install and operate.
For remote control of choke, throttle or other applications.
Solid stainless core in a non-metallic liner.
Cable can be shortened to needed dimensions.
Size: 15 feet.

SeaStar 3/8" OD nylon tubing is
recommended for inboard, sterndrive,
and SeaDrive steering systems with SeaStar
(1.7 cubic inch/rev displacement) helms only.
Length: 50'

33LU cable with Tee knob.
Easy to install and operate.
For remote control of choke, throttle or other applications.
Solid stainless core in a non-metallic liner.
Cable can be shortened to needed dimensions.
Size: 5 feet.

SeaStar 3/8" OD nylon tubing is
recommended for inboard, sterndrive,
and SeaDrive steering systems with SeaStar
(1.7 cubic inch/rev displacement) helms only.
Length: 25'

Universal, EPA compliant primer bulb.
Stainless steel bands.
Synthetic rubber bulb.
Stays flexible in cold or warm climates.
ID: 1/4".

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-3/4". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines.
Reinforced with wire helix embedded in synthetic material. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-3/8". Length: 12.5 feet.

For use with SeaStar single cylinder outboard system. Length: 27-1/2". Includes instructions.

For pivot mount cylinders. No adapters are required.

Connects fuel line assemblies and fuel tanks. Built to OEM specifications. For Yamaha engines.

Heavy duty balanced inboard brass cylinder with chrome
plated stainless steel rods & ball joint.
Stainless steel and bronze mounting hardware.
2-axis articulation.
Bore: 2"
Shaft diameter: 1"
Stroke: 11"
Volume: 26.0 cu. in.
Seal kit: HS5185
Please note that SeaStar Capilano systems use Dexron II ATF,
not SeaStar steering fluid. 

For Morse 100 series control systems. Diameter: 7/16".

Compatible with many inboard and outboard motors. Will not separate 2 cycle oil from gasoline. 21 micron filter.

For Yamaha systems. Separates water from fuel. Rated for 10 microns.

30 series cable clamp and shim kit.  
Includes 31509 cable clamp and 31538 shim.
Also includes 2 nuts and bolts.  
Plated steel.

28 Micron filter element shaped into 66 pleats-more capacity Steel end caps on elements - Heavy duty spring Powder coated outside/Epoxy coated inside, corrosion protection U.S.A. made, meets OEM specs Do not use with diesel fuel, will not separate 2 cycle oil from gas Replaces: Mercury 35-60494A4 Suzuki 99105-2000 Yamaha ABA-SEPAR-AT-OR Not recommended for 4.3 Mercruiser engines with electric fuel pumps

Separates water from gasoline.
Rated for 21 microns.

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 1".
Length: 12.5 feet.

Parts for a top mount twin setup.

Heavy-duty for hot or cold water systems. Extra wall thickness increases kink resistance. FDA-approved virgin vinyl compound. Diameter: 3/8".

Ball Joints 1-1/8" 17/32" 11/16" 5/16-24" ST 30 Series

Adapts 33C series cables to be used with OMC engine controls.

Heavy duty balanced inboard brass cylinder with bleed
fittings; chrome plated stainless steel rods & ball joint.
Stainless steel and bronze mounting hardware.
2-axis articulation.
Bore: 2"
Shaft diameter: .75"
Stroke: 7"
Volume: 18.9 cu. in.
Seal kit: HS5184
Please note that SeaStar Capilano systems use Dexron II ATF,
not SeaStar steering fluid.

SeaStar sterndrive steering cylinder.
For non-power assist steering configurations.
Bore: 1.35"
Shaft diameter: .625"
Stroke: 7"
Volume: 8.3 cu. in.
3/8” compression fittings.
Seal kit: HS5155

Replacement 33C 3300 red jacket control cable.
Stainless steel rods, hubs, and end fittings.
10-32 threaded ends, 3" covered core wires.
UV resistant polyethylene outer jacket.
Replaces your Morse 33C control cable.
Size: 17 feet.

For steering systems.
Bronze construction.