Clutch detent kit for single station
S and Twin S controls.
Includes installation instructions.

Non-permeable fuel line.
Polyester reinforced.
CPE weather and UV-resistant cover.
ID: 5/16".

This kit is designed to mount the helm
at a 20 degree angle to the mounting surface.
For raised or recessed mounts, four possible
mounting configurations are available.
Horizontal recessed mount requires HA5408 drain kit.
Not for use with BayStar helm pumps.

Spent travel tube for NFB 4.2, NFB SAFE-T II, and HPS rotary helms.

Required for converting a SyTen steering cylinder to a current SeaStar Steering cylinder.

Model CCX430. Standard replacement 4300/43 type cable With bulkhead and clamp fitting 4300/43BC type 1/4-28 threaded end. Old cable part number CC692. Length: 108" (9 feet).

Model CCX430. Standard replacement 4300/43 type cable With bulkhead and clamp fitting 4300/43BC type 1/4-28 threaded end. Old cable part number CC692. Length: 312" (26 feet).

Model CCX430. Standard replacement 4300/43 type cable With bulkhead and clamp fitting 4300/43BC type 1/4-28 threaded end. Old cable part number CC692. Length: 288" (24 feet).

Model CCX430. Standard replacement 4300/43 type cable With bulkhead and clamp fitting 4300/43BC type 1/4-28 threaded end. Old cable part number CC692. Length: 336" (28 feet).

Allows the MT-3 control to be used with 43C series cables. Includes parts and instructions.

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1".

Cable clamp shim for 30 series control cables.
Used with 32010 clamp.
7/8" center to center bolt pattern.
Overall dimensions: 1-3/8" X 1/2".
Aluminum construction.

For Teleflex CH4400, CH5600 controls. Designed for transmissions supplying a maximum of 5 amps. Right hand. Mounts in port/forward or starboard/aft positions.

Smooth cover, clear PVC with white vinyl helix. Rated for full vacuum. Resistant to mild chemicals and saltwater. Used for: - Bilge pump intake and discharge - Livewell intake and drain - Sanitation: intake, vent and pump out. Designed for connections below the waterline. Not for use in pressurized systems or with antifreeze. Diameter: 2".

For Teleflex installation purposes. Includes O-rings.

PVC hose with a flexible vinyl helix. Very flexible, abrasion, salt and chemical resistant. Used for bilge pump discharge and drains. Size: 1-1/8".

Dual station kit for Twin SR control.
For 43C series cables.
Two required for twin lever controls.

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1-1/2".

For 20 series control cables.

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1-1/4".

14" black steering wheel with 6
stainless steel spokes and hard PVC grip.
Beautiful, high-detail styling.
Rugged construction for marine use.
U.V. and corrosion resistant materials.
Stylish center medallion included.
Fits standard 3/4" tapered shaft.
Suitable for hydraulic & mechanical steering.

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 3/4".
Color: White.
50 feet per carton.

Smooth cover, clear PVC with white vinyl helix. Rated for full vacuum. Resistant to mild chemicals and saltwater. Used for: - Bilge pump intake and discharge - Livewell intake and drain - Sanitation: intake, vent and pump out. Designed for connections below the waterline. Not for use in pressurized systems or with antifreeze. Diameter: 1".

For use with water drainage. Resistant to chemicals, heat, cold, ozone, saltwater. Temperature range: -40° to -210° F. Color: Black. Diameter: 1/2".

18" SeaStar cylinder hose kit.
Used to connect 3/8" diameter copper tubing to SeaStar steering cylinders.
Adapters and compression nuts included.