Stainless steel construction.
Used for all EZ-Pull davits.
Length: 4".

Replacement arm for 3 piece davit. Aluminum construction.

Bottom pipe for EZ-Pull davit. Aluminum pipe - 53" long. Weight: 4 lbs.

Single-piece aluminum davit mount, flat top.
Mounts flush with gunnel, with pin located under gunnel.
Sleeved.

For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

1-1/2" schedule 40 aluminum davit.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

This package includes:
- Sleeved gunnel mount, flat base mount
- Aluminum pulley block
- Davit
- Electrical switch assembly
- Hauling motor.

Davit is 1-1/2" schedule 40 aluminum tubing - 64" tall and has a reach of 26".

Equipped with a 1.9 HP DC motor. This unit pulls at 140 feet per minute and has a pulling capacity of 150 pounds. Accepts line sizes 1/4" to 3/8".

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

This package includes:
- Sleeved gunnel mount, flat base mount
- Aluminum pulley block
- Davit
- Electrical switch assembly
- Hauling motor.

Davit is 1-1/2" schedule 80 aluminum tubing - 64" tall and has a reach of 26".

Equipped with a 1.9 HP DC motor. This unit pulls at 140 feet per minute and has a pulling capacity of 150 pounds. Accepts line sizes 1/4" to 3/8".

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Two-piece aluminum davit gunnel mount.
Sleeved.
Removable mount, with a 1/2" thick base plate that remains in boat.

For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

Two-piece aluminum davit base.
Sleeved.
Removable mount, with a 1/2" thick base plate that remains in boat.

For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

An octagonal shrimp pot with four tunnel entrances.
Exclusive ladder-ramp openings make this pot a top producer.
Has plenty of room to hold lots of shrimp.
High-quality vinyl-coated 14 gauge steel wire construction.
6" X 17" round bait tube, with a separate opening.
4" entrances.
Equipped with a "rottin' cotton" escape hatch that will allow shrimp to escape if pot is lost.
 
Overall dimensions: 30" X 17".
 
Not intended for commercial use. Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Single-piece aluminum davit mount.
The standard base mount for all non-HT haulers.

Pipe stub is 2-3/8" tall.
For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

Does not include sleeve.

Single-piece aluminum davit mount, with lip.
Sleeved.

For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

Sheave with roll pin. Anodized aluminum construction.

Hands-free electric crab pot puller system.
A wheel system that keeps pressure on crab pot line.
Eliminates the need to lightly pull on the rope.
Simply thread line, engage, and watch your pot come up.
Fits any of the EZ Pull units; easy to install.

Replacement sleeve for a 2" davit.

EZ-Pull electric motor package - optional 3 piece system.
Includes 12 volt electric motor assembly, including sheave, harness, and control.
Available with a standard 1.3 hp 601 express motor.
Rated for 135 to 140 feet per minute, 150 pound capacity.

Twin 50 amp breaker with busbar. For use with EZ-Puller electric pot pullers.

Single-piece aluminum davit mount.
Pipe stub is 2-3/8" tall.
Angle is 2" high.

For 1.5" davit.
Base dimensions: 3" wide, 6.5" long.

Does not include sleeve.

Replacement sleeve for a 1-1/2" davit mount.

Single-piece aluminum davit mount.
Sleeved.

For 1.5" davit.

Base dimensions: 3" wide, 6.5" long.

On/off switch for EZ-Pull.
For us with EZ-Pull electric pot pullers.

Octagonal laid-back trigger crab pot.
Three high ramp entrance tunnels with laid back triggers, built-in bait tube.
11 gauge vinyl-coated wire construction.
Side door for crab removal, top door for bait access.
Good for overnight soaks and strong current areas.
Built-in bait tube is built from 1/2" x 1" bright yellow mesh.
High ramp tunnel design is fast-catching yet holds crab securely.
The yellow bait tube brings them in and the ramps keep them there.
Dimensions: 13" X 30".

Not intended for commercial use.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

This package includes:
- Sleeved gunnel mount and sleeved deck mount
- Aluminum pulley block
- Davit
- Electrical switch assembly
- Hauling motor.

Davit is 2" schedule 80 aluminum tubing - 74" tall with a reach of 32".
Equipped with a 2.5 HP DC motor. This unit pulls 160 feet per minute, and has a pulling capacity of 225 pounds, and it accepts line sizes 1/4" to 3/8".
The manufacturer recommends this unit for pulling multiple pots on one line.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.