Vinyl-coated steel wire construction.
Built-in bait cage.
Large side and top opening hatches.
Three ramp entrances.
Stretch tube and hook closures.
Two escape rings for smaller crabs.
Dimensions: 30" X 30" X 12".

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Includes: - Red and white float - 50 feet of 1/4" poly retrival rope - Line snap and weight.

A popular crawfish trap.
Made with 1/2" X 1" vinyl-coated wire.
Features two mesh entrance tunnels and an attached bridle rope.
Opens from the top for easy bait and catch access.
Tunnel openings are approximately 7" X 7", funnels down to 2.5" X 2.5".

Made in the USA. Not intended for commercial use.
Note: Check your local and state regulations for season and gear restrictions before use.

Manufactured from 3" x 3" black vinyl coated wire.
Opens from the top for easy catch and bait access.
Features four entrance gates and includes an attached harness.

Designed for use in WA, OR, CA, AK. Please check local regulations before use.

Dimensions: 24" X 24" X 9".

Made in USA.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Rubber-wrapped rebar with stainless steel wire netting.
Two entrance tunnels.
Opens from the top for easy dumping of catch.
Dimensions: 27" X 10".

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

Promar collapsible crab pot.
Vinyl-coated steel frame.
Heavy-duty poly netting.
Three tunnel entrances.
Two 4-1/4" escape rings.
Model TR-632.
Size: 32" diameter, 12" high.

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

An octagonal shrimp pot with four tunnel entrances.
Exclusive ladder-ramp openings make this pot a top producer.
Has plenty of room to hold lots of shrimp.
High-quality vinyl-coated 14 gauge steel wire construction.
6" X 17" round bait tube, with a separate opening.
4" entrances.
Equipped with a "rottin' cotton" escape hatch that will allow shrimp to escape if pot is lost.
 
Overall dimensions: 30" X 17".
 
Not intended for commercial use. Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
14 gauge, 30" wide.
1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
16 gauge, 30" wide. 1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
14 gauge, 24" wide.
1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
16 gauge, 24" wide.
1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
14 gauge, 36" wide. 1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
16 gauge, 36" wide. 1" X 1" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

It's razor clam season! When the weather starts getting colder, it's time to head to the coast!

The Pacific razor clam is one of the most popular types of shellfish harvested in Washington state. They're super meaty with a narrow, slightly curved shell -- much like the handle or blade of an old-style straight razor. (The edge of the clamshell can be "razor-sharp" too, so watch your fingers when you're digging!)

The folks that live in the Pacific Northwest are lucky to have one of the best razor clam locations in the world. Digging for these delicious clams is a fun activity suitable for all members of your family, from kids to grandparents. Depending on where you go, you might see as many as a thousand other razor clam seekers sharing the beach. But don't worry: there are plenty of razor clams for everyone.

So how do you prepare to go razor clam digging?

You definitely need the right gear before you go.
The basic setup for a day of razor clamming includes:
 1) The correct license
 2) A clam shovel or clam gun
 3) A clam net bag to hold your catch

First, make sure you have the proper Washington state license. You will need a razor clam license to harvest clams legally (or one of the shellfish/seaweed combo licenses, there are several different kinds). You can order one online, by phone, or at an authorized license dealer. Once you have it, you'll need to keep that license in your possession while you're digging and after you've caught your limit (in case a ranger needs to inspect it).

Next, you'll need a tool to actually dig down and pull those elusive clams out of the sand. The Danielson clam gun is one option of that necessary gear (the other option is a clam shovel).

This clam gun has been engineered specifically for removing razor clams from sandy ocean beaches. Its ultra-light corrosion-resistant aluminum construction make it easy to transport, while staying strong enough to burrow into any shore in pursuit of shellfish.

Measuring 31" in length, it features a 5" x 15" barrel with a 1-3/16" x 10" T-handle with a polycarbonate lining to pad your hands a little bit. (Some people consider the aluminum Danielson razor clam gun to be the Cadillac of clam guns.)

Now, like the old-time clam expert says: "Ya can't dig ya clams at high tide." After you've found your spot at LOW tide, go searching along the shore for dimples in the sand.

So how do you use a clam gun?

Set your clam gun barrel off-center with more sand on the side facing the water. Push down while twisting back and forth, rocking in a circular manner. Once the barrel is as deep as you can go, block the air vent on the underside of the handle with your finger, then pull straight up. When you remove your finger from the vent hole, a core of sand will drop out onto the beach -- and this is where your razor clam will be, if you've got the clammer's luck.

If you want to know more about clam gun usage, try watching a video or two before you go.

Two entrance tunnels.
Opens from the top for easy dumping of crab.
Welded steel wire covered with blue powder coating.
Comes with a bait box.

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

For the CT04 and CTO3R octagon crab trap hatches. Comes assembled and ready to install. Includes biodegradable cord.

Small mesh slows crabs' access to bait.
Heavy-duty rubber band door.
Vinyl coated steel wire.

Two part kit: 
- Galvanized steel grappling hook. 
Hook has 30 feet of rope. 
- 5-1/2" white float. 
Float has 6 feet of rope and a stainless steel clip.

Galvanized steel construction. For grabbing pots out of the water. Dimensions: 8" X 5".

Crabs easily scale sloped sides, acts as inescapable pen.
Polypro net, sides have 5 strong metal supports.
Comes with harness and float.
Vinyl coated steel rings.
18" upper ring, 34" lower ring.
16" deep.

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

5" X 11" red and white float.
100 feet of leaded sinking rope.
Usable with any sport crab trap / pot.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
16 gauge, 24" wide.
1" X 1/2" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Stainless steel construction.
Three ramped entrance tunnels.
Two 4-3/8" ID escape rings.
Large latched top opens easily for you to remove your crab catch.
Has a threaded shaft for installing a zinc.
Dimensions: 32" X 12".

For use in Washington and Alaska.
Not intended for commercial use.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Corrosion-resistant plated steel wire.
Pyramid shaped trap.
Strung with tough poly take-up cords.
Size: 14" X 14".

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

A sacrificial anode helps prevent galvanic corrosion.
Cast aluminum.
Thread size: 1/2" NC.
2 lb.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
11 gauge, 36" wide.
3" X 3" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Vinyl-coated steel wire construction.
Built-in bait cage.
Large side and top opening hatches.
Four entrance gates.
Stretch tube and hook closures.
Two escape rings for smaller crabs.
Dimensions: 30" X 30" X 9".

Not intended for commercial use.
Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

May be cast with fishing rod.
Top mount swivel gives tangle free use.
2-1/2".

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

PVC coated, galvanized steel wire mesh.
For use in commercial and recreational shrimp and crab traps.
16 gauge, 24" wide.
1/2" X 1/2" spacing.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Crab caliper for Alaska, Washington, Canada, and Oregon.
Displays various sizes.

Fishing regulations change often: it is the owner's responsibility to know and follow the current federal, state and local regulations for shellfish harvesting while using this product.

These pellets are pre-soaked in special attractants and oils.
Designed to stimulate feeding activity to get your trap full.
Will last about 24 hours in the water.
May be used in any crab, shrimp or crawfish trap, simply place into a bait jar, barrel or bag.
No refrigeration necessary.

Bag size: 3 lbs.

Durable, polypropylene sinking crab line.
High strength, low stretch.
Good abrasion resistance.
Diameter: 1/4".
Tensile strength: 1,200 lb.
Color: Gray with orange tracer.
Length: 600 ft.

Rectangular weight for a crab or shrimp trap.
Weighs down the trap so it will not float out of place.
2.5 pounds.