Fynspray rocker action pump.
May be used with either fresh or salt water.
Self-priming.
Tough non-corrosive white plastic and chrome steel.

Fynspray rocker action pump. May be used with either fresh or salt water Self-priming. Tough non-corrosive black plastic and chrome steel. Weight: 1 lb.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 83 GPM - 2" NIPT - 1" diameter shaft Weight: 21 lbs

Rated for 4 gallons per minute. Suitable for diesel, fresh or salt water. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter of lay-flat hose. 12 volt DC.

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
This model is equipped with a hydraulic motor.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.

Comes with kit of tubes and hoses, reducing foot and adapter Use for bilges, sump tanks, transfer, or oil changing from engine crank case, stern drive or inboard. Tube to insert in dipstick hole for oil pump out. Tough marine plastic will not rust or corrode. No priming to start pump action. Red discharge tube, gray hand pump. Weight: .75 lb

iL500 Plus pump. Suitable for diesel, salt or fresh water. Rated for 500 gallons per hour. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter lay-flat hose. 3/4" ports. 12 volts.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Pedestal mount, corrosion resistant bronze pumps Self-priming and portable, very versatile Removable end cover allows easy impeller service Pump heads are built of bronze materials 62 GPM, 1-1/4" NIPT Port, 1" shaft, face seal, brass cam and impeller insert Weight: 12.6 lbs

For use with 1 to 5 gallon accumulator tank. Designed for 6 or more fixtures. Quiet, smooth flow. Not harmed if it runs dry. Strainer included. Plug-in ports, easy to install. May be attached to garden hose or 3/4" hose barbs.

1.24 CID hydraulic motor. 1-1/2" NPT impeller pump. 2000 maximum RPM. +/- 70 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

1.24 CID hydraulic motor. 1-1/4" NPT impeller pump. 2000 maximum RPM. +/- 55 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

Can deliver almost 7 GPM at open flow. Equipped with pressure-cast bronze body. Features a reusable O-ring type end cover seal. 1/2" internal pipe thread and 1" external hose barb. Includes 2 port adapter. 12 volt DC. Weight: 6.06 lbs

Nylon pump body. Rated for 3.5 gallons per minute. Activates at 25 PSI, cuts out at 40 psi. Quiet operation, smooth flow. Compact design. 3/8" port, 1/2" hose output. 12 volt DC.

Johnson Aqua Jet water pressure system. A postive displacement diaphragm pump for small craft. Works great for pressurized water supply systems. Rated for 3.5 GPM. 3/8" NPT, 1/2" hose ports. Weight: 5.5 lbs.

Thermoplastic pump body. Rated for 5 gallons per minute. Stainless steel shaft. 3/4" ports. 12 volts DC.

A variable speed drive system. Adds pressure-sensor control to everyday pumps. Senses real-time changes in pressure. Provides smooth and pulsation-free performance. Works on most water presure systems. 12 volts.