A multi-purpose hand pump kit. Brass and neoprene construction. Corrosion resistant. Great for draining or filling engine and gearbox oil. Rated for up to 1-1/2 GPM output. Includes: - Pump - Two 1/2" hoses, 3 feet length - Two dipstick probes, 1/4" and 5/16" - Connector and adapter for 1/2" hose. Not designed for pumping flammable liquids.

Includes: - 3 feet of 1/2" hose - Probe adaptor - 1/4" X 40" dipstick probe - Utility pump. Kit has same utility pump as 17250-0003. Packed in poly bag with display header card.

FC Tournament Series pump.
For seacock applications.
3/4" intake.
3/4" discharge hose.
Flow rate: 800 GPH.
12 volts.

Has some of the most advanced features in the industry. Automatic operation, with a non-clogging electric float. Removable motor cartridge for cleaning and replacement. Rated for 750 GPM. Equipped with easy-to-install Dura-Port discharge ports. 3/4" fitting. Dimensions: 3" X 4" X 4.4".

Bronze impeller pump. Can handle small bilge debris. Flow rate: 8 GPM. 12 volts.

For use with 1 to 5 gallon accumulator tank Designed for 6 or more fixtures Quiet smooth flow No harm if runs dry. Strainer included. Plug-in ports, easy install: 2 for garden hose and 2 for 3/4" hose barb. Weight: 6 lbs

Rated for 5 gallons per minute. 70 PSI maximum pressure. Includes: - Pump - 25 feet of coiled hose - Pump protector inlet strainer - Spray nozzle - Two-way panel switch with fuse.

Dockside general purpose pumping and some onboard uses.
Self-priming and portable, very versatile.
Removable end cover allows easy impeller service.
Pump heads are built of bronze materials.

FC Tournament Series livewell pump.
3/4" straight pickup tube.
1/2" port for washdown pump attachment.
500 GPH.
Discharge: 3/4".
12 volts

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 2A Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 15.25 lbs

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Quick-release strainer allows for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 53S.
2000 GPH.

High-capacity bilge pump, designed for the toughest applications.
An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
2" discharge outlet.
Model number: 56D.
Rated for 4000 GPH.

Automatic bilge pump: with a built-in sensor, the pump will activate when water is present and stop after it's pumped out.
Fully submersible.
May be connected to a three-way switch for a manual override option.
3/4" discharge outlet. 
12 volt DC. 
Rated for 800 GPH. 

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.
Pedestal mount.

Rated for 14 gallons per minute. Cast bronze cutter plate macerator. Reduces particle size to 1/8". Nitrile impeller with stainless steel wearplates. Inlet: 1-1/2". Outlet: 1".

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
This model is equipped with a hydraulic motor.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 3" FNPT.

Comes with kit of tubes and hoses, reducing foot and adapter Use for bilges, sump tanks, transfer, or oil changing from engine crank case, stern drive or inboard. Tube to insert in dipstick hole for oil pump out. Tough marine plastic will not rust or corrode. No priming to start pump action. Red discharge tube, gray hand pump. Weight: .75 lb

A variable speed drive system. Adds pressure-sensor control to everyday pumps. Senses real-time changes in pressure. Provides smooth and pulsation-free performance. Works on most water presure systems. 12 volts.