Replacement pump only, does NOT include clutch. Has a connection for a vacuum switch accessory. Bronze construction. Mechanical seal, stainless steel shaft. 1-1/2" ports.

A centrifugal booster pump. Bronze construction. 1/2" inlet and outlet. 12 volt.

Provides pumping power at the push of a button. Has a connection for a vacuum switch accessory. Bronze construction. Mechanical seal, stainless steel shaft. 1-1/4" ports.

Tournament series, high-capacity pump.
Rated for 1600 gallons per hour.
Bronze base.
1" ports.
12 volts.

For quick, easy and clean oil changes.
Includes dipstick probe and a female garden hose connector.
Reversible flow.
12 volt model with 8' cord and alligator clips.

Solid brass piston rod for strength & durability. Easily disassembled for cleaning. 1-1/2" barrel means quick pumpouts. 5 year warranty. Includes 24" of 1-1/8" black bilge flex hose.

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Self-priming, very easy to clean.
Will not rust or corrode.
Length: 36".
1-3/4" diameter.
13 GPM pump rate.
Does not include a outlet hose.

Flexible impeller self priming bronze pedestal pump.
Typical Marine Applications:
-Engine cooling
-Bilge pump
-Wash-down pump
-Emptying holding tanks  
Bronze body. 3/8" NPT ports.  Rated for 6 GPM at 1800 RPM.  Neoprene impeller. 3/8" stainless steel shaft.
Caution: Do not run dry.

Pump with neoprene impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Plastic pump body. Nitrile valves and diaphragm. Rated for 8.1 gallons per minute. 1-1/2" ports. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 10-6UL.
2000 GPH.
Has 6-foot wire leads for easy installation.

Thirsty-Mate high capacity super pump. Coast Guard approved for commercial use. Model 519CG#2. Three strokes per gallon, rated for 22 gallons per minute. Inlet hose is 24", outlet hose is 72". Length: 24". Diameter: 3". Weight: 8.3 lbs.

Heavy-duty bilge pump. Liquid-cooled, 12-pole motor with double ball bearings. Stainless steel and strong plastic construction. Operates at 120 l/min, 1900 GPH. 4.5 amps, 6 amp fuze. 1-1/8" and 1-1/4" connectors.

A rotary cutter shreds waste before it is pumped into or out of the holding tank The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet 15 amp - 1-1/2" hose or 1-1/2" NPT inlet - 1" hose outlet Weight: 5.1 lbs

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/8" discharge outlet.
Model number: 03.
1500 GPH.

Connects to marine engine oil dipstick tubes. Fits threaded male garden hose fitting. Unique design allows one hand pumping. Includes: - Pump with 3/4" brass fitting - Drain hose, 1/2" X 2' length.

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Diameter: 1-3/4". Length: 36". Strokes per gallon: 4.

Polypropylene pump body
Rated for 5.2 gallons per minute
Activates at 25 PSI, cuts out at 40 psi
Quiet operation, smooth flow
Has a 2 liter accumulator tank
1/2" hose output
12 volt DC.

Similar in design to an electromagnetic clutch pump. Equipped with a mechanically activated clutch. Provides added operational security in case of power failure Rated for 26 gallons per minute. 1" port.

Reliable, rugged diaphragm pump.
Portable, lightweight.
All Delrin plastic construction.
Self-priming.
12 foot delivery suction lift.
Horizontal handle orientation.
Inlet / outlet diameter: 1".

1.8 CID hydraulic motor. 2" NPT impeller pump. 2000 maximum RPM. +/- 90 GPM of water at 2000 RPM. 15 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
12 volt DC.

Bilge pump for larger boats. Rated for 1500 gallons per minute. Uses 1-1/8" hose. Meets USCG/ABYC standards. Equipped with a quick-release strainer base. Weight: 3.1 lbs.

Engine Cooling Pump & General Purpose Pumping 3.7 GPM, 1/4" NIPT Port Connections. Pedestal mount, corrosion resistant bronze pumps: Use for engine cooling, washdown, circulation, & general purposes on-board or dockside. Bronze or stainless steel shaft installed with permanently lubricated ball bearings for long life & heavy-duty service. Self-priming with ability to operate in either direction at variable speeds. Capacity ranges from 3 GPM to 83 GPM with varied port configurations and sizes. Most models have replaceable cams/wearplates for extended product life. Removable end cover for easy impeller service. Standard impeller for these pump models is neoprene. (some have alternative oil resistant nitrile impellers available.)

Submersible bilge pump - 600 gallons per hour. Tough enough for any bilge. Built from impact resistant ABS. Stainless steel hardware and shaft. Strainer base is quick-release for easy cleaning. Hose: 3/4". Weight: .8 lb.

A flexible impeller pump. Vertically oriented ports. Mechanical face seal, double row ball bearings. Neoprene impeller. 1" NPT. Overall dimensions: 7" X 4-1/4" X 4".

For use with Beckson 118P Thirsty-Mate hand pump.
Diameter: 1-1/4".

Plastic pump body. Designed to provide constant water pressure. 3/8" ports. Automatic flow from tank to faucet. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 13A.
3700 GPH.
Includes a five-year warranty from Xylem.

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Length: 24".

Designed for washdown or for livewell tanks.
Heavy-duty construction.
Ideal for commercial or pleasure boats.
1-1/2" inlet, 1-1/2" discharge outlet.
Rated for 3700 GPH.
Must be mounted below waterline.
Operates at low pressure; not self-priming.
24 volts DC.

Jabsco 50900 Fish Box evacuation pump. A single-diaphragm, 5 GPM plastic-body pump. Perfect for emptying the fisbox after a day's fishing. This self-priming pump is designed to pass debris, such as bait residue, ice particles, fish scales, etc. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Great for evacuating small boats. Keep it on hand for emergencies. 36" long hose.

Self-priming hand pump.
Great for evacuating small boats.
Stash one in your canoe, kayak or dinghy.
Comes complete with a removable hose.