Shields 400/402 Vinylvent Vent Hose 4" 4 1/8" 10 White Venting of bilge gases & fumes. PVC hose supported by helical wire. Resistant to ozone, sunlight and weathering. Will not support a flame.

Flexible impeller self priming bronze pedestal pump.
Typical Marine Applications:
-Engine cooling
-Bilge pump
-Wash-down pump
-Emptying holding tanks  
Bronze body. 3/8" NPT ports.  Rated for 6 GPM at 1800 RPM.  Neoprene impeller. 3/8" stainless steel shaft.
Caution: Do not run dry.

Stainless steel.
Diameter: 2-1/2".

High-pressure cut off switch.

Pump with neoprene impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Nitrile. 6 blades. Diameter: 1-9/16".

Plastic pump body. Nitrile valves and diaphragm. Rated for 8.1 gallons per minute. 1-1/2" ports. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 10-6UL.
2000 GPH.
Has 6-foot wire leads for easy installation.

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1/2".

Replacement volute for "S" Pacer pump. Diameter: 3".

Fuel/water filter canister. Not for use with diesel systems. Weight: .5 lb.

Fuel filter, 5/16" - 3/8". A universal in-line filter. Clear body for quick visual inspections. Protects fuel systems from pollutants. Fits fuel lines from 1/4" to 3/8" ID. NOT for use on inboard engines. Weight: .3 lb.

Knitted-nylon reinforcement.
Tough, weather-resistant vinyl cover.
Excellent handling, even in cold weather.
Solid brass full flow couplings.
5/8" diameter.
100 feet long.

Fuel filter and water separator kit Includes: - Reusable filter head - Water separating fuel filter - 3/8 hose barbs and plugs. Corrosion resistant. For gasoline engines only, NOT diesel. Flow: 20 liters per minute @ 60 psi. Weight: 1 lb.

Thirsty-Mate high capacity super pump. Coast Guard approved for commercial use. Model 519CG#2. Three strokes per gallon, rated for 22 gallons per minute. Inlet hose is 24", outlet hose is 72". Length: 24". Diameter: 3". Weight: 8.3 lbs.

PVC hose with a flexible vinyl helix. Very flexible, abrasion, salt and chemical resistant. Used for bilge pump discharge and drains. Size: 3/4".

Heavy-duty bilge pump. Liquid-cooled, 12-pole motor with double ball bearings. Stainless steel and strong plastic construction. Operates at 120 l/min, 1900 GPH. 4.5 amps, 6 amp fuze. 1-1/8" and 1-1/4" connectors.

U-bolt style exhaust clamp. 
Secures exhaust tubing. 
Diameter: 4-1/2".

Used with standard 10" filter housings (#4-6 10230).

Part number #4-6 15029.

Tohatsu/Nissan fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Tohatsu/Nissan fuel tank connector - male Chrome brass construction. Size: 1/4" NPT. Weight: .1 lb.

Tohatsu/Nissan fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Tohatsu/Nissan tank connector - male. Chrome brass construction. Size: 1/4" NPT. Weight: .1 lb.

Suzuki fuel line connector - female. Chrome brass construction. Size: 3/8". Weight: .1 lb.

Suzuki/Honda fuel line connector - male. Chrome brass construction. Size: 1/4". Weight: .1 lb.

Honda fuel tank connector - female. Steel / plastic two-prong clip style construction. Size: 3/8". Weight: .1 lb.

Mercury fuel line assembly. Comes complete with primer bulb and fittings. Fuel line is 7 feet long. Surpasses CARB requirements. Size: 3/8" hose barb. Weight: .1 lb.

Honda fuel tank connector - male. Brass construction. Size: 1/4". Weight: .1 lb.

Mercury fuel tank connector - male. Prong clip style tank fitting. Brass construction. Size: 1/4" NPT. Weight: .1 lb.

Non-permeable fuel line. Polyester reinforced. CPE weather and UV-resistant cover. ID: 3/8".

Forespar MF 849 flange mounting seacock. Molded in high strength glass-reinforced Marelon. Strong, lightweight, and corrosion resistant. Uses a ball valve to control flow. For controlling water needs above or below the waterline. Diameter: 3/4". Weight: .4 lb.

Forespar MF 849 flange mounting seacock. Molded in high strength glass-reinforced Marelon. Strong, lightweight, and corrosion resistant. Uses a ball valve to control flow. For controlling water needs above or below the waterline. Diameter: 1/2".

8 blades. Dimensions: 2-9/16" X 1-7/16". Shaft diameter: 5/8".

A rotary cutter shreds waste before it is pumped into or out of the holding tank The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet 15 amp - 1-1/2" hose or 1-1/2" NPT inlet - 1" hose outlet Weight: 5.1 lbs