Rated for high temperature. Diameter: 3".

Cast bronze. Diameter: 1".

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 3".
Length: 12.5 feet.

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
12 volts DC.

Nylon pump body. Rated for 3.5 gallons per minute. Activates at 25 PSI, cuts out at 40 psi. Quiet operation, smooth flow. Compact design. 3/8" port, 1/2" hose output. 12 volt DC.

Johnson Aqua Jet water pressure system. A postive displacement diaphragm pump for small craft. Works great for pressurized water supply systems. Rated for 3.5 GPM. 3/8" NPT, 1/2" hose ports. Weight: 5.5 lbs.

Diameter: 3/16". 50 foot coil.

Jabsco 50890 waste pump. A single-diaphragm, 5 GPM plastic-body pump. This self-priming pump is designed to pass debris. No filter required. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Clear plastic. Designed for easy inspection. Diameter: 5/16".

Thermoplastic pump body. Rated for 5 gallons per minute. Stainless steel shaft. 3/4" ports. 12 volts DC.

Prevents damage to lines due to rubbing and chafing. Color: Blue. 2-1/2" filled. 4" flat.

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 3/8".

Black smooth vinyl cover with a helix. Rated for full vacuum. Resistant to chemicals and saltwater. Primarily used for bilge pump and discharge purposes. Easily bent, OK for below waterline connections. Diameter: 1-1/2".

Black smooth vinyl cover with a helix. Rated for full vacuum. Resistant to chemicals and saltwater. Primarily used for bilge pump and discharge purposes. Easily bent, OK for below waterline connections. Diameter: 1-1/4".

For low-flow applications with space restrictions. Clear styrene acrylonitrile for easy flow viewing. Used with a 5" X 2-1/2" filter cartridge.

For engine cooling pumps. 12 blades. Diameter: 2.56".

For use with water drainage. Resistant to chemicals, heat, cold, ozone, saltwater. Temperature range: -40° to -210° F. Color: Black. Diameter: 3/4".

Prevents damage to lines due to rubbing and chafing. Color: Blue. 1-1/2" filled. 2.5" flat.

Fuel pump made by Walbro for Dickinson stoves. 2-3.5 psi fuel pump. Use for fuel transfer to day tank or supply to Dickinson stoves or heaters. Part # 20-000. Weight: 3 lbs.

Fuel pump made by Walbro for Dickinson stoves. 2-3.5 psi fuel pump with regulator. Adjustable pressure, standard 12V. Use for fuel transfer to day tank or supply to Dickinson stoves or heaters. Part # 20-002.

Diameter: 1" NPT.
Stainless steel.

Non-asbestos synthetic fiber, with a steel core.
Designed for exhaust manifolds and flanges.

Temperature rating: 1200° F.
Diameter: 5".

Replacement for the Jabsco 6760-0001 and Johnson 09-802B impellers. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Replacement fuel filter element. 25 micron element for inline fuel filter. Includes required gaskets. Part # 20-020.

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 1" Hose Size: 1" Overall Length: 4-3/4" Weight: .6 lbs

Fuel filter with shut-off valve. A perfect filter for a Dickinson stove. Stainless steel and glass filter. Stone element included. Part # 20-010. Weight: .6 lbs

Continuous duty motor and thermal overload protection Self primes up to 10' above the bilge Manual on/off switch or automatic level control connect to pump No harm if pump runs dry Includes 3/4" barb inlet strainer Fitting: Plug-in ports, easy installing, 2 for garden hose and 2 for 3/4" hose barb Weight: 6 lbs

Quick, easy and clean oil changes at flip of a switch Removes oil/sludge through dip stick tube so engine oil changes quick and easy. No spill under engine. Oil changer supplied with both 1/4" x 40" dipstick probe and a female garden hose connector that attaches suction hose directly to dipstick tubes supplied with male garden hose threads. Reversible pump so container is emptied neatly/easily by reversing flow direction. Retractable pouring spout if not desirable to use pump for emptying. 12 volt model with 8' cord and alligator clips. Simply connect power cord to appropriate electrical source. With flick of switch sturdy motor pump unit drains crankcase into its 14 qt. holding container. Dimensions: Height 13-5/8", Width 13-1/2" 
 

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 5/8".

Reliable, rugged diaphragm pump. Portable, lightweight. All Delrin plastic construction. Self-priming. 12 foot delivery suction lift. Vertical handle orientation. Inlet / outlet diameter: 1-1/2".

Neoprene. 12 blades. Diameter: 2-1/4".

Nitrile. 12 blades. Diameter: 2-1/4".

Replacement for the Jabsco 836-0001 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 1-1/4" Hose Size: 1-1/4" Overall Length: 5-1/2" Weight: 1 lb

Neoprene. 10 blades. Diameter: 2-9/16".