Bronze construction. Nitrile impeller. Lip seal, stainless steel shaft. 1/2" ports, horizontal orientation.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 11.3 GPM - 1/2" NIPT - 5/8" diameter shaft Weight: 4.51 lbs

Fire-retardant marine fuel hose. Resists alcohol-enhanced gasolines. High nitrile rubber construction. Reinforced with two spirals of synthetic fabric. Diameter: 1/2". 50 feet per box.

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 1-1/2".

Rated for 5 gallons per minute. 70 PSI maximum pressure. Includes: - Pump - 25 feet of coiled hose - Pump protector inlet strainer - Spray nozzle - Two-way panel switch with fuse.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2". Length: 12.5 feet.

Neoprene. 9 blades. Diameter: 3-3/4".

Nitrile. 9 blades. Diameter: 3-3/4".

304 stainless steel. 1-1/4" X 1-1/2".

Nitrile rubber. 10 blades Diameter: 1-19/32".

King Nipple - Straight Standard Flow 1/2" NPT x 1/2" hose - Bronze Weight .17 lbs

Dockside general purpose pumping and some onboard uses.
Self-priming and portable, very versatile.
Removable end cover allows easy impeller service.
Pump heads are built of bronze materials.

FC Tournament Series livewell pump.
3/4" straight pickup tube.
1/2" port for washdown pump attachment.
500 GPH.
Discharge: 3/4".
12 volts

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 1-1/8".
Color: Black.
50 feet per box.

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 1-1/2".

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 1-1/4".

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 2A Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 15.25 lbs

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-5/8". Length: 12.5 feet.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Quick-release strainer allows for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 53S.
2000 GPH.

Heavy-duty for hot or cold water systems. Extra wall thickness increases kink resistance. FDA-approved virgin vinyl compound. Diameter: 1/4".

Cast aluminum king combination nipples. Hose diameter: 2" Thread size: 2"

Cast aluminum king combination nipples. Hose diameter: 1-1/2" Thread size: 1-1/2" Weight: .01 lbs.

Cast aluminum king combination nipples. Hose diameter: 1-1/4" Thread size: 1-1/4" Weight: .01 lbs.

High-capacity bilge pump, designed for the toughest applications.
An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
2" discharge outlet.
Model number: 56D.
Rated for 4000 GPH.

Cast aluminum king combination nipples. Hose diameter: 1" Thread size: 1"

Multi-purpose agriculture petroleum hose.
For grease, gasoline, kerosene, and other oils.
Diameter: 3/4".

For use with 1 to 5 gallon accumulator tank Designed for 6 or more fixtures Quiet smooth flow No harm if runs dry. Strainer included. Plug-in ports, easy install: 2 for garden hose and 2 for 3/4" hose barb. Weight: 6 lbs

Double-ply soft wall, no wire. 
For straight connection in wet exhaust systems. 
Okay for either gasoline or diesel engines. 
Designed for coolant and heat resistance. 
Color: Black with blue stripe. 
Temperature range: 0° to 212° F. 
Diameter: 1/1/2". 
Length: 12.5 feet.

Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact us for shipping options.

Separates water from fuel. Rated for 10 microns.

Automatic bilge pump: with a built-in sensor, the pump will activate when water is present and stop after it's pumped out.
Fully submersible.
May be connected to a three-way switch for a manual override option.
3/4" discharge outlet. 
12 volt DC. 
Rated for 800 GPH. 

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.
Pedestal mount.

Rated for 14 gallons per minute. Cast bronze cutter plate macerator. Reduces particle size to 1/8". Nitrile impeller with stainless steel wearplates. Inlet: 1-1/2". Outlet: 1".

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
This model is equipped with a hydraulic motor.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 3" FNPT.

Designed to connect a tank to a wall mount regulator.
High-pressure rated.
Male POL to 1/4" inverted flare.
Length: 20".
UL listed.

Traps dirt and metallic particles. Lets you immediately inspect your fuel condition. Not for use on inboard engines. Includes connection barbs in 1/4", 5/16", 3/8".