Pedestal mount.
For power or sailboats up to 65 feet.
Black polycarbonate construction.
Seawater resistant.
Height: 5".
White LED.

For use with Jabsco searchlights. Diameter: 7". 12 volts. 100 watts.

Includes: - Twist-lock 305 CRPN male plug - 102N contoured weather-resistant cover - Two Velcro cord organizer straps. 30 amp, 125 volt.

Rated for 3 amps. Does not include deck outlet. Length: 1-3/8". Display packaged.

Bilge water level warning system. Uses a loud bell and red panel light to signal "High Water." Includes bell, bilge water level detector, and warning light Easily connected to 32 volt marine systems. Weight: 3 lbs.

Brass and Bakelite construction. Flush cap. Marked "FUSE". 10 amps, 12 volts. Display packaged.

200 watts, 120 volts. For Aqua Signal floodlights.

"Reduced glare" cockpit light lens and gasket. Designed to direct 80% of light downward. Installs into a 2-1/8" diameter hole. For replacing damaged or worn lenses. Manufacturer's #: 1146DP099A. Weight: .08 lb.

Double contact Clear Nominal Wattage: 12 Wattage: 11

Nylon cable clamps - 25 pack. Cast from a strong, flexible material. Resistant to solvents, oils, acids and moisture. Unique screw hole alignment feature speeds installation. Absorbs shock and vibration; reduces unwanted noise. Size: 3/16". Weight: .04 lb.

Pure nylon for maximum strength. Resistant to solvents, oils, acids and moisture. Unique screw hole alignment feature for quick installations. Absorbs shock and vibration; reduces unwanted noise. Pack: 100. Size: 1/4". Color: White.

Nominal voltage: 12. Wattage: 10. Amps: .83.

Manufactured from tinned copper with a flexible vinyl coating for corrosion prevention.
Resists cold, salt water, UV rays, and many petrochemicals.
Meets ABYC, UL & USCG requirements.

100 foot spool; also available by the foot.

Color: Red.

NOTE: When purchasing full rolls, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Snap-on terminal cover insulates all conductive parts, satisfying ABYC/USCG requirements.
Cover breakouts allow wires from sides or bottom.
Terminal screws compress fuse blades within blocks for low resistance connections.
Ignition protected.
Label recess accepts large format label.
Fuses sold separately.

Quartzline halogen bulb 1500 watts, 208 volts. NMP, double ended. Q1500T3.

A versatile, all-around light, recently updated.
Uses 20 high-output white LEDs, projecting over 15000 lumens.
Optics are shaped for spotlight / floodlight coverage.
Surface mounts, with an included bracket.
Length: 10".

Male connector: 50 amp, 125/250 volt, locking. (Attaches to dockside receptacle or cord set.) Female connector: 2-30 amp, 125 volt, locking with collar. (Attaches to cordset or to boat inlet.)

Replaces standard 24" fluorescent tubes.
Frosted, for diffuse lighting.

Installation requires removal of fluorescent ballast 

Adhesive lined heat shrink ring terminals. Cross linked polyolefin tubing is much stronger than PVC. Heat activated adhesive lining provides impervious seals. Protects from saltwater, oil, acid, sunlight, and strain. Able to shrink down to 1/3 of original size. Pure copper for maximum current flow. Wire size: 16-14 gauge. Stud size: 3/8". 3 per pack. Weight: .03 lb

Adhesive lined heat shrink ring terminals. Cross linked polyolefin tubing is much stronger than PVC. Heat activated adhesive lining provides impervious seals. Protects from saltwater, oil, acid, sunlight, and strain. Able to shrink down to 1/3 of original size. Pure copper for maximum current flow. Wire size: 22-18 gauge. Stud: #10. 3 per pack. Weight: .02 lb.

Replaces standard 24" fluorescent tubes. 
Installation requires removal of fluorescent ballast. 
Clear tube.

Replaces standard 48" fluorescent tubes. 
Installation requires removal of fluorescent ballast.
Frosted tube.

ABS plastic for corrosion resistance. 
Comes with a three-way switch for auto/manual modes. 
Equipped with a 20 amp circuit breaker.