Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match fir wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match oak wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match mahogany wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match red oak wood. Size: 1/4 pint. Weight: .47 lb.

Unique vinylester formula designed for marine filling and fairing uses above and below waterline.
Cures tack-free in 30 minutes.
Made with 3M Scotchlite glass bubbles for sanding ease.
Size: 1 quart.

'Wood Flour' is ground and filtered natural bark. Mixes with epoxy to form a wood-colored, sandable surface. Simply add Wood Flour until desired consistancy is reached. Used when a hard solid for filling and filleting is required Size: 1/2 gal. Weight: 1 lb.

Milled fibers (1/32" milled fiberglass). Used when epoxy must fill a void and provide extremely high strength and resistance to cracking. Ideal for structural filleting and hardware bonding. Simply add to mixed epoxy. Size: 1/2 gallon. Weight: .2 lbs.

Phenolic micro balloons, organic phenolic hollow spheres Low density, lightweight epoxy additive. Used when sandable, paint-ready surfaces are required. Ideal for fairing. Size: 1/2 gallon. Weight: .6 lbs.

CAB-O-SIL fumed colloidal silica. Adds strength to epoxies. Creates an extremely hard, high-density solid finish. Ideal for structural bonding, filling, and filleting. Simply add into mixed epoxy. Absolutely clear finish when dry; no white residue. Size: 1/2 gallon. Weight: .25 lbs.

Quick hardening, non-separating, cream hardener.
Formulated for use with body fillers, specialty fillers and polyester finishing putties.
Color: Blue.
Size: 1 oz.

Make gelcoat quality repairs with a simple paste. For fixing scratches, nicks, and gouges. Mixes with Evercoat color agents to match your original hue. Will adhere to gelcoat, fiberglass and most woods and metals Size: 1 pt.

High quality, white plastic filler. For permanent repair of fiberglass, wood, metal. Useful for filling dents, scrapes and gouges. Will not shrink, crack, or pop out after curing. Can be tinted with coloring agents. Includes hardener. Size: 1/2 pint.

High quality, white plastic filler. For permanent repair of fiberglass, wood, metal. Useful for filling dents, scrapes and gouges. Will not shrink, crack, or pop out after curing. Can be tinted with coloring agents. Includes hardener. Size: 1 pint

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 4 oz.

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 quart.

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 pint.

Unique vinylester formula designed with short strand fiberglass for semistructual repairs, above and below waterline Repairs areas of fiberglass hulls, decks, and other parts Cures tack-free in 30 minutes Weight: 11.58 lbs

Unique vinyl ester formula. For semistructual repairs, above or below waterline. Fixes fiberglass hulls, decks, and other parts. Cures tack-free in 30 minutes. Color: Off-white. Size: 1 qt.

'Wood Flour' is ground and filtered natural bark. Mixes with epoxy to form a wood-colored, sandable surface. Simply add Wood Flour until desired consistancy is reached. Used when a hard solid for filling and filleting is required Size: 1 quart. Weight: .5 lbs.

Milled fibers (1/32" milled fiberglass). Used when epoxy must fill a void and provide extremely high strength and resistance to cracking. Ideal for structural filleting and hardware bonding. Simply add to mixed epoxy. Size: 1 quart. Weight: .1 lbs.

Phenolic micro balloons, organic phenolic hollow spheres.
Low density, lightweight epoxy additive.
Used when sandable, paint-ready surfaces are required.
Ideal for fairing.
Size: 1 qt.

CAB-O-SIL fumed colloidal silica.
Adds strength to epoxies.
Creates an extremely hard, high-density solid finish.
Ideal for structural bonding, filling, and filleting.
Simply add into mixed epoxy.
Absolutely clear finish when dry; no white residue.
Size: 1 quart.

Cell-O-Fill epoxy filler. A fibrous, all-natural cellulose epoxy additive. Reduces sagging and slumping when applying MAS epoxy. Will not billow in the air like silica. Comes as a non-toxic white powder. Size: 1 quart. Weight: 2 lbs.

Best known for its bridging capabilities in rebuilding shattered fiberglass and for reinforcing torn or rusted areas of sheet metal.
Formulated with long strands of chopped fiberglass.
Double the strength of standard fillers.
Waterproof and rustproof.
Can be used with or without fiberglass cloth or mat.
Should be finished with Rage and / or Metal Glaze.
Blue cream hardener included.

Aluminum body repair filler For metal surfaces. Has excellent corrosion resistance properties. Adheres well to galvanized steel and aluminum. Will not sag: known as "the nearest thing to lead". Moisture proof. Easily sands to a fine feather edge. Metal-2-Metal liquid reactor included. Size: 1 qt.

The original polyester glazing putty Can be applied directly to bare metal, body filler, fiberglass and fully cured sanded top coats. Easily fills grind marks, pinholes, low spots and other minor imperfections. Contains ZNX-7 for superior adhesion to galvanized steel, bare steel, aluminum, SMC, E-Coat and OEM finishes. No shrinkage. Easy dry. Reduces risk of staining. Blue cream hardener included. Weight: 2.75 lb

Quick hardening, non-separating, cream hardener.
Formulated for use with body fillers, specialty fillers and polyester finishing putties.
Color: White.
Size: 4 oz.

A lightweight, fast-curing, two-part epoxy putty.
For filling and smoothing surface imperfections.
Safe for use above and below the waterline.
An integral part of Pettit's gelcoat blister repair system.
Also used for leveling metal keels or other underwater areas.
Excellent chemical and water resistance.
Non-sagging, non-shrinking and easy to apply.
Color: Off-white.
Size: 1.5 quarts.

A lightweight, fast-curing, two-part epoxy putty.
For filling and smoothing surface imperfections.
Safe for use above and below the waterline.
An integral part of Pettit's gelcoat blister repair system.
Also used for leveling metal keels or other underwater areas.
Excellent chemical and water resistance.
Non-sagging, non-shrinking and easy to apply.
Color: Off-white.
Size: 8.5 ounces.

High quality, white plastic filler. For permanent repair of fiberglass, wood, metal. Useful for filling dents, scrapes and gouges. Will not shrink, crack, or pop out after curing. Can be tinted with coloring agents. Includes hardener. Size: 1 quart

Paintable, non-toxic sealant that is pliable and soft. It can be used on oddly shaped gaps and holes. Does not damage or corrode plastic or metal. 1 lb. block.

Fix repair putty. A non-sagging repair putty that cures like steel. May be used underwater. Once cured, Fix putty may be drilled, sanded and painted. Bonds well to fiberglass, wood, metal, glass and concrete. Easily cleaned up with soap and water (before cure). Size: 3 oz. Weight: .2 lb.

Premium filler is tack-free and stain-free Reduces risk of staining top coats Will not load or clog sandpaper. No cheese grating needed. Cures to non-tacky surface in 15-20 minutes. Blue cream hardener included. Weight: 9.25 lbs