High solids non-skid epoxy.
Heavy-duty grit helps shoes grip ramps/decks.
Used on aircraft carriers worldwide.
Two-part, cure and resin.
Color: Dark gray.
Size: 5 gal.

An "All-in-One" primer.
Single-part multipurpose primer for above the waterline.
Combines the features of separate substrate primers in one.
Adheres well to wood, fiberglass, metals on bare or painted surfaces.
Excellent covering capability, high build, good grain filling.
Provides corrosion protection on steel.
Color: White.
Size: 2 liters.

Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: Pearl Gray. Size: 1 gal.

Deep penetrating wood conditioner. Appropriate for interior and exterior use. Becomes integral part of wood and hardens wood. Does not leave surface film. Reduces chance of grain raising. Practically odorless/colorless. Will not crack, chalk, blister or peel. Pre-conditioning to staining. Size: 1 pint.

Deep penetrating wood conditioner. Appropriate for interior and exterior use. Becomes integral part of wood and hardens wood. Does not leave surface film. Reduces chance of grain raising. Practically odorless/colorless. Will not crack, chalk, blister or peel. Pre-conditioning to staining. Size: 1 quart.

A two-part water-based epoxy primer / sealer.

May be used on concrete, masonry, fiberglass, wood and previously painted substrates.
This primer is recommended for your projects with Tuff Coat for proper adhesion.
Simple 1:1 mix.

1 quart kit.

Multi-purpose, two-part epoxy primer. Used above waterline. Undercoats for Interlux Perfection coating. Great for application to rough surfaces. Will resurface cracked or damaged gelcoat.

Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: White. Size: 1 gal.

Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: Red. Size: 1 gal.

General purpose tie coat primer.
Use above or below waterline.
Compatible with anti-fouling bottom paints.
Compatible with all types of single component topside finishes.

C.I.P - Corrosion Inhibiting Primer. Penetrates and stabilizes surfaces. Creates a solid, stable base layer for other coatings. For use on new or rusted surfaces, interior or exterior. Great for protecting from severe environmental conditions. Size: 2.5 liter.

Quick hardening, non-separating, cream hardener.
Formulated for use with body fillers, specialty fillers and polyester finishing putties.
Color: Blue.
Size: 1 oz.

Make gelcoat quality repairs with a simple paste. For fixing scratches, nicks, and gouges. Mixes with Evercoat color agents to match your original hue. Will adhere to gelcoat, fiberglass and most woods and metals Size: 1 pt.

High quality, white plastic filler. For permanent repair of fiberglass, wood, metal. Useful for filling dents, scrapes and gouges. Will not shrink, crack, or pop out after curing. Can be tinted with coloring agents. Includes hardener. Size: 1/2 pint.

High quality, white plastic filler. For permanent repair of fiberglass, wood, metal. Useful for filling dents, scrapes and gouges. Will not shrink, crack, or pop out after curing. Can be tinted with coloring agents. Includes hardener. Size: 1 pint

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match fir wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match oak wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match mahogany wood. Size: 1/4 pint. Weight: .47 lb.

Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match red oak wood. Size: 1/4 pint. Weight: .47 lb.

Unique vinylester formula designed for marine filling and fairing uses above and below waterline.
Cures tack-free in 30 minutes.
Made with 3M Scotchlite glass bubbles for sanding ease.
Size: 1 quart.

'Wood Flour' is ground and filtered natural bark. Mixes with epoxy to form a wood-colored, sandable surface. Simply add Wood Flour until desired consistancy is reached. Used when a hard solid for filling and filleting is required Size: 1/2 gal. Weight: 1 lb.

Milled fibers (1/32" milled fiberglass). Used when epoxy must fill a void and provide extremely high strength and resistance to cracking. Ideal for structural filleting and hardware bonding. Simply add to mixed epoxy. Size: 1/2 gallon. Weight: .2 lbs.

Phenolic micro balloons, organic phenolic hollow spheres Low density, lightweight epoxy additive. Used when sandable, paint-ready surfaces are required. Ideal for fairing. Size: 1/2 gallon. Weight: .6 lbs.

CAB-O-SIL fumed colloidal silica. Adds strength to epoxies. Creates an extremely hard, high-density solid finish. Ideal for structural bonding, filling, and filleting. Simply add into mixed epoxy. Absolutely clear finish when dry; no white residue. Size: 1/2 gallon. Weight: .25 lbs.

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 4 oz.

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 quart.

Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 pint.

Penetrates raw wood.
Gives improved stability and moisture resistance.
Prevents excessive absorption of undercoaters and varnishes.
Tung/linseed oil phenolic based resin.
Not for use on teak.
Applies easily by brush or spray.
Size: 1 quart.

Anticorrosive primer for underwater metal. Great for running gear and lower units. Superb corrosion barrier, reduces metal pitting. Usable over incompatible or unknown antifouling paints. Matte finish. Apply below waterline. Color: YPA984 Gray. Size: 1 gallon.

A unique two part epoxy primer coating.
Helps to prevent and repair gelcoat blistering.
Protects fiberglass hulls from water absorption.
Gives excellent barrier coat protection.
Contains "micro-plates" for extra protection.
Works as an anti-corrosive substrate primer for metals.
Dries quickly, with a short re-coat time.
Color: Gray.
Size: 1 gallon kit.

A unique two part epoxy primer coating.
Helps to prevent and repair gelcoat blistering.
Protects fiberglass hulls from water absorption.
Gives excellent barrier coat protection.
Contains "micro-plates" for extra protection.
Works as an anti-corrosive substrate primer for metals.
Dries quickly, with a short re-coat time.
Color: Gray.
Size: 1 quart kit.

Anticorrosive primer for underwater metal. Great for running gear and lower units. Superb corrosion barrier, reduces metal pitting. Usable over incompatible or unknown antifouling paints. Matte finish. Apply below waterline. Color: YPA984 Gray. Size: 1 quart.

An anti-corrosive primer for underwater metal surfaces. Provides an excellent barrier to reduce pitting. Great for use before antifouling paint on fiberglass.

An "All-in-One" primer.
Single-part multipurpose primer for above the waterline.
Combines the features of separate substrate primers in one.
Adheres well to wood, fiberglass, metals on bare or painted surfaces.
Excellent covering capability, high build, good grain filling.
Provides corrosion protection on steel.
Color: White.
Size: 3/4 liter.

ePaint epoxy primer converter.
Must be mixed with ePaint EP-PRIME resin.
Gives extraordinary corrosion resistance.
Used for prepping surfaces for ePaint bottom coating.
Size: 1 qt.