Z6_GHK6HJC0OG6S20Q8HU3K6R0G63
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM5
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM7
Z7_GHK6HJC0OG6S20Q8HU3K6R0Q22
-Manufacturers
View:
BoxesList
Quick View
High solids non-skid epoxy.
Heavy-duty grit helps shoes grip ramps/decks.
Used on aircraft carriers worldwide.
Two-part, cure and resin.
Color: Dark gray.
Size: 5 gal.
Item#:
DEV138GDG5G
Manufacturer:
PPG / Ameron
Available:
Out of Stock
$1,460.03
Your Price:
$1,095.02
EACH
Call to Order
Quick View
An "All-in-One" primer.
Single-part multipurpose primer for above the waterline.
Combines the features of separate substrate primers in one.
Adheres well to wood, fiberglass, metals on bare or painted surfaces.
Excellent covering capability, high build, good grain filling.
Provides corrosion protection on steel.
Color: White.
Size: 2 liters.
Item#:
EPFMMPW2000
Manufacturer:
Epifanes N.A.
Available:
In Stock
$158.47
Your Price:
$103.01
EACH
Add to Cart
Quick View
Amercoat 5105 alkyd primer
Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: Pearl Gray. Size: 1 gal.
Item#:
DEV5105PEGG
Manufacturer:
PPG / Ameron
Available:
In Stock
 
Ground Shipping Only
$105.18
Your Price:
$128.01
EACH
Add to Cart
Quick View
Benite wood conditioner
Deep penetrating wood conditioner. Appropriate for interior and exterior use. Becomes integral part of wood and hardens wood. Does not leave surface film. Reduces chance of grain raising. Practically odorless/colorless. Will not crack, chalk, blister or peel. Pre-conditioning to staining. Size: 1 pint.
Item#:
DLY11080
Available:
Out of Stock
 
Ground Shipping Only
$40.60
Your Price:
$34.51
EACH
Call to Order
Quick View
Benite wood conditioner
Deep penetrating wood conditioner. Appropriate for interior and exterior use. Becomes integral part of wood and hardens wood. Does not leave surface film. Reduces chance of grain raising. Practically odorless/colorless. Will not crack, chalk, blister or peel. Pre-conditioning to staining. Size: 1 quart.
Item#:
DLY11040
Available:
In Stock
 
Ground Shipping Only
$54.87
Your Price:
$46.64
EACH
Add to Cart
Quick View
Amercoat 5105 alkyd primer
Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: Red. Size: 1 gal.
Item#:
DEV5105ORG
Manufacturer:
PPG / Ameron
Available:
Out of Stock
 
Ground Shipping Only
$170.68
Your Price:
$128.01
EACH
Call to Order
Quick View
A two-part water-based epoxy primer / sealer.

May be used on concrete, masonry, fiberglass, wood and previously painted substrates.
This primer is recommended for your projects with Tuff Coat for proper adhesion.
Simple 1:1 mix.

1 quart kit.
Item#:
PET40004001Q
Manufacturer:
Pettit Paint / Kop-Coat
Available:
In Stock
$75.91
Your Price:
$69.08
EACH
Add to Cart
Quick View
PrimeKoat epoxy kit
Multi-purpose, two-part epoxy primer. Used above waterline. Undercoats for Interlux Perfection coating. Great for application to rough surfaces. Will resurface cracked or damaged gelcoat.
Item#:
INT404G
Manufacturer:
Interlux Paint
Available:
Out of Stock
 
Ground Shipping Only
$286.27
Your Price:
$171.76
EACH
Call to Order
Quick View
Amercoat 5105 alkyd primer
Corrosion-resistant primer for structural steel. Intended to be covered with alkyd topcoating. Single component, resists corrosion, sprays well. Contains no lead or chrome pigments. Suitable for exterior and interior steel surfaces. Color: White. Size: 1 gal.
Item#:
DEV5105W
Manufacturer:
PPG / Ameron
Available:
In Stock
 
Ground Shipping Only
$170.68
Your Price:
$128.01
EACH
Add to Cart
Quick View
Quick hardening, non-separating, cream hardener.
Formulated for use with body fillers, specialty fillers and polyester finishing putties.
Color: Blue.
Size: 1 oz.
Item#:
FGE100361
Manufacturer:
Evercoat Co.
Available:
In Stock
$7.23
Your Price:
$6.00
EACH
Add to Cart
Quick View
Polyester Gel-Paste
Make gelcoat quality repairs with a simple paste.
For permanent gelcoat repairs - scratches, nicks, gouges, etc.

Mixes with Evercoat color agents to match your original hue.
Will adhere to gelcoat, fiberglass and most woods and metals.

Size: 16 oz. (1 pt.)
Item#:
FGE100695
Manufacturer:
Evercoat Co.
Available:
In Stock
$78.51
Your Price:
$65.16
EACH
Add to Cart
Quick View
Formula 27 All-Purpose Filler
High quality, white plastic filler.

For permanent repair of fiberglass, wood, metal.
Useful for filling dents, scrapes and gouges.
Will not shrink, crack, or pop out after curing.
Can be tinted with coloring agents.

Includes hardener.

Size: 1/2 pint.
Item#:
FGE100572
Manufacturer:
Evercoat Co.
Available:
In Stock
$37.38
Your Price:
$31.02
EACH
Add to Cart
Quick View
Formula 27 All-Purpose Filler
High quality, white plastic filler.

For permanent repair of fiberglass, wood, metal.
Useful for filling dents, scrapes and gouges.
Will not shrink, crack, or pop out after curing.
Can be tinted with coloring agents.

Includes hardener.

Size: 1 pint.
Item#:
FGE100571
Manufacturer:
Evercoat Co.
Available:
In Stock
$60.76
Your Price:
$50.43
EACH
Add to Cart
Quick View
Evercoat’s easiest sanding body filler.
Stain resistant for use with basecoat/clearcoat paints.
May be used for heavy filling applications.
Creamy formula is easy-to-mix, spread, and sand.
Provides superior adhesion and featheredging.

1 gallon.

Part of the MetalWorks® System.

Blue cream hardener included.
Item#:
FGE100112
Manufacturer:
Evercoat Co.
Available:
In Stock
$150.26
Your Price:
$124.71
EACH
Add to Cart
Quick View
MAS 'Wood Flour' - 1/2 gallon
'Wood Flour' is ground and filtered natural bark. Mixes with epoxy to form a wood-colored, sandable surface. Simply add Wood Flour until desired consistancy is reached. Used when a hard solid for filling and filleting is required Size: 1/2 gal. Weight: 1 lb.
Item#:
MAS25-021
Manufacturer:
MAS Epoxies
Available:
In Stock
 
Ground Shipping Only
$34.45
Your Price:
$24.12
EACH
Add to Cart
Quick View
Milled fibers - 1/2 gallon
Milled fibers (1/32" milled fiberglass). Used when epoxy must fill a void and provide extremely high strength and resistance to cracking. Ideal for structural filleting and hardware bonding. Simply add to mixed epoxy. Size: 1/2 gallon. Weight: .2 lbs.
Item#:
MAS25-006
Manufacturer:
MAS Epoxies
Available:
In Stock
 
Ground Shipping Only
$89.27
Your Price:
$62.49
EACH
Add to Cart
Quick View
Phenolic micro balloons
Phenolic micro balloons, organic phenolic hollow spheres Low density, lightweight epoxy additive. Used when sandable, paint-ready surfaces are required. Ideal for fairing. Size: 1/2 gallon. Weight: .6 lbs.
Item#:
MAS25-008
Manufacturer:
MAS Epoxies
Available:
In Stock
 
Ground Shipping Only
$75.18
Your Price:
$52.63
EACH
Add to Cart
Quick View
CAB-O-SIL colloidal silica
CAB-O-SIL fumed colloidal silica. Adds strength to epoxies. Creates an extremely hard, high-density solid finish. Ideal for structural bonding, filling, and filleting. Simply add into mixed epoxy. Absolutely clear finish when dry; no white residue. Size: 1/2 gallon. Weight: .25 lbs.
Item#:
MAS25-002
Manufacturer:
MAS Epoxies
Available:
Out of Stock
 
Ground Shipping Only
$39.16
Your Price:
$27.41
EACH
Call to Order
Quick View
Famowood wood filler - 1/4 pt.
Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match fir wood. Size: 1/4 pint. Weight: .47 lb.
Item#:
FAM36041116
Manufacturer:
Eclectic Products
Available:
In Stock
$5.67
Your Price:
$4.54
EACH
Add to Cart
Quick View
Famowood wood filler - 1/4 pt.
Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match oak wood. Size: 1/4 pint. Weight: .47 lb.
Item#:
FAM36041128
Manufacturer:
Eclectic Products
Available:
Out of Stock
$5.67
Your Price:
$4.54
EACH
Call to Order
Quick View
Famowood wood filler - 1/4 pt.
Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match mahogany wood. Size: 1/4 pint. Weight: .47 lb.
Item#:
FAM36041122
Manufacturer:
Eclectic Products
Available:
Out of Stock
$6.25
Your Price:
$5.00
EACH
Call to Order
Quick View
Famowood wood filler - 1/4 pt.
Famowood wood filler. A professional wood flour-based substance. May be stained, sawed, drilled, sanded and more. Will fill just about any hole or crack. Colored to match red oak wood. Size: 1/4 pint. Weight: .47 lb.
Item#:
FAM36041134
Manufacturer:
Eclectic Products
Available:
Out of Stock
$5.67
Your Price:
$4.54
EACH
Call to Order
Quick View
Unique vinylester formula designed for marine filling and fairing uses above and below waterline.
Cures tack-free in 30 minutes.
Made with 3M Scotchlite glass bubbles for sanding ease.
Size: 1 quart.
Item#:
THM46005
Manufacturer:
Three M (3M) Marine
Available:
In Stock
$140.24
Your Price:
$105.18
Add to Cart
Quick View
Git Rot liquid epoxy kit
Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 4 oz.
Item#:
BTL1063
Manufacturer:
BoatLife / Life Ind.
Available:
Out of Stock
 
Ground Shipping Only
$34.54
Your Price:
$29.36
EACH
Call to Order
Quick View
Git-Rot liquid epoxy kit
Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 quart.
Item#:
BTL1065
Manufacturer:
BoatLife / Life Ind.
Available:
In Stock
 
Ground Shipping Only
$133.13
Your Price:
$113.16
EACH
Add to Cart
Quick View
Git-Rot liquid epoxy kit
Repairs dried-out, rotted, and weathered wood. This unique two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot. Actually works with the loose rotted fibers. Wood must be dry before application. Apply by injecting into wood. The epoxy will soak into wood by capillary action.

One-half hour pot life after mixing. Sandable, paintable, and can be drilled and screwed. Compatible with fiberglass resins, epoxies and most sealants. Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.

How to use Git-Rot:
 
First, locate the dry rot. There are a couple of techniques you can use to find dry rot - try tapping suspect areas with a hard instrument and listen for those "hollow-sounding" dead spots. Use a knife to probe where you think water is likely to pool or places that are constantly being re-wetted. In particular, make sure you check around hatches, seams, transom, planking, toe rails, stem and ribs.

For maximum strength and saturation, you will need a volume of Git-Rot epoxy approximately equal to half the volume of the rotted wood. When using Git-Rot, only mix small batches (around 4 oz.) since the larger the quantity, the greater the reaction and the faster the cure. Mix 1 part "B" and 3 parts "A", and shake vigorously for a minute. Immediately apply to the dry rotted area -- the epoxy penetrates best immediately after it's mixed. It will solidify overnight, but needs a full week for maximum strength.

Size: 1 pint.
Item#:
BTL1064
Manufacturer:
BoatLife / Life Ind.
Available:
In Stock
 
Ground Shipping Only
$78.89
Your Price:
$67.06
EACH
Add to Cart
Quick View
ePaint epoxy primer, Haze Gray
ePaint Multi-Purpose epoxy primer.
A robust, easy-to-use two part primer.
Perfect as a base coat for ePaint antifouling paint.
Provides water migration and corrosion protection.
Compatible with bottom paints, easy to apply.
Size: 1 gal.
Color: Haze Gray.
Item#:
EPCP1000705G
Manufacturer:
E Paint Co.
Available:
Out of Stock
 
Ground Shipping Only
$208.32
Your Price:
$145.82
EACH
Call to Order
Quick View
Clear sealant
Penetrates raw wood.
Gives improved stability and moisture resistance.
Prevents excessive absorption of undercoaters and varnishes.
Tung/linseed oil phenolic based resin.
Not for use on teak.
Applies easily by brush or spray.
Size: 1 quart.
Item#:
PET2018Q
Manufacturer:
Pettit Paint / Kop-Coat
Available:
In Stock
 
Ground Shipping Only
$43.57
Your Price:
$39.65
EACH
Add to Cart
Quick View
Primocon underwater primer
Anticorrosive primer for underwater metal. Great for running gear and lower units. Superb corrosion barrier, reduces metal pitting. Usable over incompatible or unknown antifouling paints. Matte finish. Apply below waterline. Color: YPA984 Gray. Size: 1 gallon.
Item#:
INTYPA984G
Manufacturer:
Interlux Paint
Available:
In Stock
 
Ground Shipping Only
$225.44
Your Price:
$135.26
EACH
Add to Cart
Quick View
InterProtect epoxy kit
A unique two part epoxy primer coating.
Helps to prevent and repair gelcoat blistering.
Protects fiberglass hulls from water absorption.
Gives excellent barrier coat protection.
Contains "micro-plates" for extra protection.
Works as an anti-corrosive substrate primer for metals.
Dries quickly, with a short re-coat time.
Color: Gray.
Size: 1 gallon kit.
Item#:
INT2000EG
Manufacturer:
Interlux Paint
Available:
Out of Stock
 
Ground Shipping Only
$272.22
Your Price:
$163.33
EACH
Call to Order
Quick View
InterProtect epoxy kit
A unique two part epoxy primer coating.
Helps to prevent and repair gelcoat blistering.
Protects fiberglass hulls from water absorption.
Gives excellent barrier coat protection.
Contains "micro-plates" for extra protection.
Works as an anti-corrosive substrate primer for metals.
Dries quickly, with a short re-coat time.
Color: Gray.
Size: 1 quart kit.
Item#:
INT2000EQ
Manufacturer:
Interlux Paint
Available:
In Stock
 
Ground Shipping Only
$91.16
Your Price:
$54.70
EACH
Add to Cart
Quick View
Primocon underwater primer
Anticorrosive primer for underwater metal. Great for running gear and lower units. Superb corrosion barrier, reduces metal pitting. Usable over incompatible or unknown antifouling paints. Matte finish. Apply below waterline. Color: YPA984 Gray. Size: 1 quart.
Item#:
INTYPA984Q
Manufacturer:
Interlux Paint
Available:
In Stock
 
Ground Shipping Only
$70.79
Your Price:
$42.48
EACH
Add to Cart
Quick View
An anti-corrosive primer for underwater metal surfaces. Provides an excellent barrier to reduce pitting. Great for use before antifouling paint on fiberglass.
Item#:
INTYPA985
Manufacturer:
Interlux Paint
Available:
In Stock
 
Ground Shipping Only
$54.23
Your Price:
$32.54
EACH
Add to Cart
Quick View
An "All-in-One" primer.
Single-part multipurpose primer for above the waterline.
Combines the features of separate substrate primers in one.
Adheres well to wood, fiberglass, metals on bare or painted surfaces.
Excellent covering capability, high build, good grain filling.
Provides corrosion protection on steel.
Color: White.
Size: 3/4 liter.
Item#:
EPFMMPW750
Manufacturer:
Epifanes N.A.
Available:
In Stock
$65.01
Your Price:
$42.25
EACH
Add to Cart
Quick View
ePaint EP-PRIME converter
ePaint epoxy primer converter.
Must be mixed with ePaint EP-PRIME resin.
Gives extraordinary corrosion resistance.
Used for prepping surfaces for ePaint bottom coating.
Size: 1 qt.
Item#:
EPCEP1000CQ
Manufacturer:
E Paint Co.
Available:
Out of Stock
 
Ground Shipping Only
$49.60
Your Price:
$34.72
EACH
Call to Order
Quick View
Single-component low VOC universal primer.
May be used on both ferrous and galvanized metal.
Fast-drying properties.
Excellent corrosion resistance.
May be top coated.
Lead and chromate free.
High volume of solids.
Color: White.
Size: 1 gal.
Item#:
DEV4360WG
Manufacturer:
PPG / Ameron
Available:
In Stock
$165.86
Your Price:
$124.39
EACH
Add to Cart
View:
BoxesList