Engine, pump, tank, filter: a self-contained unit.
Fully assembled and mounted with stainless steel fasteners.
Marine-grade aluminum base with aluminum handle.
11 GPM 4-stroke, 13 horsepower Honda gasoline engine.
Suitable for powering 12" hauler head assemblies.
Electric-start enabled.

NOTE: Engine on this power pack is shipped WITHOUT oil.
Fill engine with oil to proper lever before starting.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Needed for electrically actuated EX38 valves.
12 volt DC.
With # SAE ORB "Y" port.

Walvoil EX38 full flow sharing sectional valve. 
- Pressure-compensated flow control work sections 
- Sectional valve (1-10 sections) 
- Load sensing 
- Full flow pressure relief 
For use with mechanical, hydraulic, pneumatic and proportional electro-hydraulic controls. 
Manually actuated, spring to center spool. 
16 GPM. 
#10 SAE ORB Work ports 

Pressure compensated flow controlled sections.
Load sense configuration, adjustable pressure relief.
1 spring work section / 2 friction work sections.
Available in 16 GPM or 22 GPM work sections.

Gear motor assembly.
Series 26.
Bi-directional.
Straight shaft, 5/8".
Mounts with 2-bolt "A" SAE flange series 82-2.
1.24 displacement.

Open center / cylinder spool. 12 GPM rated flow. 3625 PSI maximum work pressure. P, A, and B ports #8 SAE O-ring. T port #10 SAE O-ring. Spring to neutral. Nickel plated spool. 2 banks.

NBR seals.
Loadsense.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 125.
Flow rating: 12.5 liters / minute.
Displacement: 7.3 cubic inches.

Open center / cylinder spool. 12 GPM rated flow. 3625 PSI maximum work pressure. P, A, and B ports #8 SAE O-ring. T port #10 SAE O-ring. Spring to neutral. Nickel plated spool.

Direct replacement for your twister or rotate mounting bracket 180 degrees for internal mount.
Direct drive 50 cubic inches.
Radial piston cam-lobe motor.
Highly efficient with very low noise.
Approximately 1000 lb. torque at 1450 PSI.
150 maximum RPM.
400 maximum RPM (freewheeling).
Compatible with open or closed loop hydraulic systems.
Standard 6 bolt flange with pilot.
Direct twister replacement.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Rated for 4 GPM. Right hand.

High-pressure through-deck (bulkhull) fitting. Stainless steel construction. Rated for 3000 psi, for use with hydraulic systems. Two female NPT ports: 3/4". Overall dimensions: 5.5" X 3".

Hydraulic quick-connect fitting.
#12.
Size: 3/4".
Rated for 0 - 3000 PSI.

For use with fairlead roller. Size: 4".

Monoblock valve.
Fitted with a pressure relief valve and load check valve.
Simple, compact, heavy-duty.
Available in a wide variety of port configurations, spool types, and spool control kits.
18 GPM.
Max operating pressure: 4600 PSI.
Inlet/outlet ports: #10 SAE ORB.
Work ports: #8 SAE ORB.
Outlet port back pressure rating: 360 PSI.
Banks: 1.
Friction hold.
Cylinder spool.

Monoblock valve.
Fitted with a pressure relief valve and load check valve.
Simple, compact, heavy-duty.
Available in a wide variety of port configurations, spool types, and spool control kits.
18 GPM.
Max operating pressure: 4600 PSI.
Inlet/outlet ports: #10 SAE ORB.
Work ports: #8 SAE ORB.
Outlet port back pressure rating: 360 PSI.
Banks: 1.
Rotary.
Cylinder spool.

Open center. Power beyond. Non load reaction.

Stainless steel. #6 COMP to #6 MJIC.

Stainless steel.
#6 MJIC to #4 MBSPP.

Rated for 25 GPM. 100 mesh. Dimensions: 2" X 1-1/4".

Stainless steel splitter. For 14" blocks.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 22.6 CID.
1" straight keyed shaft.
4-bolt square flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 9.7 CID.
1" straight keyed shaft.
4-bolt square flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 5.9 CID.
1" straight keyed shaft.
4-bolt square flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 11.3 CID.
1" straight keyed shaft.
4-bolt square flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 14.1 CID.
1" straight keyed shaft.
4-bolt square flange.
Manifold ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 11.3 CID.
1" straight keyed shaft.
4-bolt square flange.
Manifold.

Zinc-plated steel.
Elbow.
#8 MJIC to #12 MBSPP.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors
provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 11.3 CID.
1" straight keyed shaft.
2-bolt SAE-A flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 22.6 CID.
1" straight keyed shaft.
2-bolt SAE-A flange.
1/2" NPT ports.

A direct interchange with Eaton/Charlynn (and other brands).
May be used for series or parallel applications.
FluiDyne's low speed, high-torque motors
provide superior performance with:
- Low-pressure start-up
- High-pressure shaft seals
- Low noise with proprietary fluid distribution system
- Longer life with special driver-link design
- Easy installation with compact design.
Displacement: 14.1 CID.
1" straight keyed shaft.
2-bolt SAE-A flange.
1/2" NPT ports. 

Steel construction. 3/4" NPTF. 25 GPM. 5000 PSI.

Length: 10 feet.
1/2" pitch.
Size: #40.
Meets ASME/ANSI B29.1 standards.
Stocked in 10' lengths; available by the inch or foot.

Size: 1/2" X 2".

Connects the two ends of a roller chain. Regular steel. Size: #60.

Transparent polyamide resin construction.
Guard is steel with black finish.
Rated for a maximum operating temperature of 212° F.
Compatible with petroleum-based fluids.
Maximum pressure: 44 PSI.
Nitrile seal.
Size: 5".

Buna N spider insert cushion for Lovejoy coupling hub. Insert material is nitrile butadiene rubber. Oil resistant and highly resiliant for a long life. Coupling size: L075.