Stainless steel construction. 3/4" tapered shaft. 5" shaft.

Open center / cylinder spool. 20 GPM rated flow. 3625 PSI maximum work pressure. P, A and B ports #10 SAE O-ring. T port #12 SAE O-ring. Spring to neutral. Nickel-plated spool.

#4 HS to #2 MNPT.

Plated steel.
#8 female JIC to #10 male JIC.

Plated steel.
#8 female JIC to #12 male JIC.

Used as a drum motor.
Features:
- 63.9 CID
- 2-1/4" straight keyed shaft
- Standard mount SAE-5
- #12 SAE ORB Ports
- Max speed: 90 RPM continuous
- Max flow: 25 GPM continuous
- 1412.5 ft/lb max torque continuous
- Max PSI: 2000 PSI continuous.

Shaft drilled and tapped.
Single vane pump only.
2-bolt A flange mount.
Right hand rotation.
13 GPM at 1200 RPM.
Inlet: 1-1/4" NPT.
Outlet: 3/4" NPT.

Plated steel. #16 female JIC to #20 male JIC.

Synthetic Nitrile rubber hose.
Reinforced with four-wire spiral steel wire.
Meets MSHA fire resistance standards.
Very flexible.
OK for use with petroleum, polyol ester, or water/glycol.
Diameter: 3/4".

#24 male JIC to #20 male NPT.

- 39 GPM maximum inlet flow
- 5000 PSI maximum inlet pressure
- 145 PSI maximum back pressure outlet port
- #12 SAE ORB pressure port
- #12 SAE ORB return port
- #6 SAE ORB load sense port.

Aluminum construction.
Comes complete with pin.
For 14" hauler.
Diameter: 4".

Hydraulic quick-connect fitting.
#4.
Size: 1/4".
Rated for 0 - 3000 PSI.

#12 FJIC to #12FJIC connector / adapter.

Walvoil EX38 end cover - standard end plate.

For DPX100 valve section.

Hydraulic quick-connect fitting.
#16.
Size: 1".
Rated for 0 - 3000 PSI.

Direct replacement for your twister or rotate mounting bracket 180 degrees for internal mount.
Direct drive 63 cubic inches.
Radial piston cam-lobe motor.
Highly efficient with very low noise.
Approximately 1230 lb. torque at 1450 PSI
130 maximum RPM 400 maximum RPM freewheeling.
Compatible with open or closed loop hydraulic systems.
Standard 6 bolt flange with pilot. Direct twister replacement.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Hydraulic quick-connect fitting.
#4.
Size: 1/4".
Rated for 0 - 3000 PSI.

Plated steel. #6 female JIC to #8 male JIC.

Replacement shaft for motor. 14 teeth.

Union. 
Stainless steel. 
#12 compression fitting to #12 compression fitting.

Stainless steel. 
#10 compression fitting to #10 male JIC

Stamped stainless steel discs For 10" hauling block.

Union. 
Stainless steel. 
#8 compression fitting to #8 compression fitting. 

Stainless steel hub For 10" hauling block.

For use with a Hydrocontrol D4 sectional valve.
Four bolts (with nuts and washers) per kit.

Stainless steel splitter. For 10" haulers.

Union. 
Stainless steel. 
#10 compression fitting to #10 compression fitting. 

Open center. 25 GPM. 5000 PSI maximum. Spring to center with fourth position float. Fourth position allows for anchor winch freewheel.

Forged stainless steel.
For 12" hauler block.

Hydraulic steering control unit
Closed center
Load sensing.
NBR seals.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 100.
Flow rating: 10 liters / minute.
Displacement: 5.9 cubic inches.

Engine, pump, tank, filter: a self-contained unit.
Fully assembled and mounted with stainless steel fasteners.
Marine-grade aluminum base with aluminum handle.
11 GPM 4-stroke, 13 horsepower Honda gasoline engine.
Suitable for powering 12" hauler head assemblies.
Electric-start enabled.

NOTE: Engine on this power pack is shipped WITHOUT oil.
Fill engine with oil to proper lever before starting.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Needed for electrically actuated EX38 valves.
12 volt DC.
With # SAE ORB "Y" port.

Walvoil EX38 full flow sharing sectional valve. 
- Pressure-compensated flow control work sections 
- Sectional valve (1-10 sections) 
- Load sensing 
- Full flow pressure relief 
For use with mechanical, hydraulic, pneumatic and proportional electro-hydraulic controls. 
Manually actuated, spring to center spool. 
16 GPM. 
#10 SAE ORB Work ports