Vented male helm pump plug.
Must be used with helm pump on all single
steering station systems.
Must also be used on uppermost helm pump on
multi-steering station systems.
Ergonomic design to assist with the
installation and removal resulting in less
chance of over-tightening leading to damage.

Non-vented male helm pump plug.
Must be used on all helm pumps other than uppermost helm
pump on multi-steering station systems.
Ergonomic design to assist with the installation and removal
resulting  in less chance of over-tightening leading to
damage.

This kit makes bleeding and purging your SeaStar hydraulic steering system much easier.
Seastar suggests: first, pre-fill your helm, attach the filler kit with a quart of SeaStar fluid (HA5430H), puncture the bottom end of the bottle with the included pushpin, and begin the bleeding process.

This kit is designed to retrofit a new
SeaStar helm into a larger dash cut out (4.5")
or reduce helm protrusion from the dash by
the thickness of the dash.
Not for use with Baystar helm pumps.

Bleed tee (TM Cylinders).
3/4" UNF 45˚ flare (1/2" tube) X 3/8" NPT X bleed nipple.
Two per package.

Vertical bleed tee.
3/8" compression X 3/8" NPT X bleed nipple.
Two per package.

3/8” compression X 1/4" MNPT 90˚ elbow.
Three per package.

Horizontal bleed tee.
3/8" compression X 1/4" NPT X bleed nipple.
Two per package.

3/8" compression tube nut.  
For use with 3/8" nylon and/or 3/8" copper tubing.
Six per package.

3/8" compression tee.
Three per package.

Bleed nipple.
Includes O-ring.
For use with front mount cylinders only.
Two per package.

Replacement fill plug. For use with all Marol helm models.

Female #6 SAE 45° swivel X 3/8" ID hose.
Brass construction.                      
Field attachable.                        
Fits MSH-6 hose.  

Connects fuel line assemblies and fuel tanks. For Nissan / Tohatsu. 1/4".

Connects fuel line assemblies and fuel tanks. For Mercury (1998 and newer). 1/4".

Engineered to repel water and remove contaminates.
A primary/secondary filter for 500 series turbine assemblies.
Filter is 10 microns.

Built to strict OEM standards. Designed for use with Honda outboard systems. Attaches to the fuel hose on the engine side. Size: 1/4".

Designed to absorb angular prop thrust loads.
Heavy-duty aluminum casting.
Oil and fuel resistant elastomer element.
Comes complete with nuts and washers.

Water absorbing filter.
10 microns.
Height: 7".
Diameter: 5".

Diesel filter assembly with drain - 15 GPH 2 micron element, see-thru bowl, primer bulb

Engineered to repel water and remove contaminates.
Used as a secondary filter for 500 series turbine assemblies
Filter is 2 microns.

For Racor 900 or 1000 fuel filter/water seperators.

Designed to absorb angular prop thrust loads. 
Heavy-duty aluminum casting. 
Oil and fuel resistant elastomer element. 
Comes complete with nuts and washers.
3/4”-16 Fine thread main stud.
1/2” Diameter mount holes are 5” apart.
Overall mount dimension: 6.5” length by 3.375” width. 

10 micron. Replaces filter to Unit 660. For gasoline.

Connects fuel line assemblies and fuel tanks. For Chrysler engines. 5/16".

Kit includes all needed seals and O-rings for a rebuild of a Racor 500 fuel filter system.
Manufacturer's number: #RK15211.

Built to strict OEM standards. Designed for use with Nissan / Tohatsu outboard systems. Attaches to the fuel hose on the engine side. Size: 3/8".

Connects fuel line assemblies and fuel tanks. For Suzuki. 1/4".

Built to strict OEM standards. Designed for use with Suzuki outboard systems. Attaches to the fuel hose on the engine side. Size: 3/8".

Rated for 90 GPH. 2 micron filter. Four port head with 3/8" NPT. Metal bowl (UL Listed). For inboard or outboard applications. Gasoline use only.

Can is fluted for improved installation Fits Cummins 5.9L Turbo Diesel Engine Replaces Chrysler 5083285AA O.D.:3-11/16 - Length: 7-1/8 Interior Gasket: G381-A Weight: 1 lb

Connects fuel line assemblies and fuel tanks. For Nissan / Tohatsu. 1/4".

Connects fuel line assemblies and fuel tanks. For Mercury. Female (1998 and newer). 3/8".

Built to strict OEM standards. Designed for use with Honda outboard systems. Attaches to the fuel hose on the engine side. Size: 3/8".