MECHANICAL STEERING | HYDRAULIC STEERING
MECHANICAL ENGINE CONTROLS | HYDRAULIC ENGINE CONTROLS
The Engine and Steering Controls are divided into 4 sections. Click on the section above that will get you where you need to go!
A Proven System for Maximum Performance
Instatrim, the original
hydraulic boat leveler, provides a better ride every time you leave the
dock. A simple rocker type control permits you to correct a bow high or
list condition on any shape hull, from 16 to 60 feet. Easy to install Instatrim
boat levelers are strong and durable, and come in lengths to fit most boats.
Custom sizes are available too, so any boating enthusiast can enjoy a superior
ride. Instatrim's over 25 year commitment to the boating industry assures
you of a quality product and an excellent performance.
Benefits:
• Easily Installed
Comes pre-assembled with mounting hardware. They are easily and quickly
installed, and a minimum of time is required.
• Level Ride
Instatrim boat levellers put you boat in proper trim and corrects listing,
making for a smooth, enjoyable ride for you and your passengers.
• Increased Visibility
A level ride improves the skipper's visibility. You and your passengers
are more secure and boating safety is improved immeasurably.
• Improved Performance
Instatrim boat levelers allow you to throttle back regardless of load and
speed.
• Wiring
Color-coded wiring in 25' to 40' lengths with quick connect fittings,
meets federal standards for heat, pull and insulation, making installation
easy.
• Solenoids
They are custom designed for Instatrim boat leveler company, epoxy sealed
and humidity resistant, thereby preventing shorting out. The solenoids
lock the tabs in any position, eliminating driftback. Barb type hose fittings
provide tight, secure connections.
• Motor
A powerhouse with coated wirings and a thermal ovreload that resists temperature
and amperage build-up. 1-3/4" stack windings and top mounting eliminates
oil leakage. The motor is mounted with stainless steel nuts and bolts,
and is easily disassembled.
• Pump
Designed and engineered exclusively by Instatrim. The built-in bypass is
factory set at 400 P.S.I. tolerance held to ±.00025. Amperage doesn't
have to exceed 16 because the unit circulates oil, rather than stalling
out or trying to pump additional pressure.
• Brackets
Swivel type brackets allow cylinders to be mounted and adjusted to
ant angle. Knockout pins act as shear pins if tab strikes an object.
• Cylinders
Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion
and resists ultra-violet rays. Two expanding type seals, plus O-ring eliminates
high an low pressure leaks. Barbed cylinder fitting and an inserted tubular
rod prevents hose blow-off and breakage. A stainless steel spring retracts
the cylinder when the boat is not in motion.
• Trim Tabs
12 gauge 304 stainless steel trim tabs are available in standard and custom
lengths. They are guaranteed against electrolysis, remaining strong and
secure. Instatrim's hinges prevent most spray and can be used for transom
or bottom mounting.
• Rocker Type Controls
Mounted on the dash they are easy to operate. 2TP Micro swiitch with
silver contact points adjust the tabs for maximum control and performance.
One pint of transmission fluid, funnel and mounting hardware is supplied.
Stock # Boat Type Boat Length Tab Size
* Two hydraulic cylinders
per tab.
Top
Steering your Auxiliary Motor Couldn't be "E.Z."er.
•Increases safety and convenience
•Lets you steer your auxiliary engine from your boat's main wheel
•No more steering while hanging over the transom with a restricted view
•The patented self-adjusting, stainless steel rod attaches between your
boat's main and auxiliary engines
•There is no need to disconnect the unit to make a main power run
•As long as you can steer your main engine, you'll be able to steer your
auxiliary, even if one is raised or tilted
•It's the only self-adjusting auxiliary steering rod
•Perfect for hassle free trolling and boating
•Made in USA using DuPont® Delrin ball joints with brass inserts for
rust resistance
•Mounting brackets are vinyl coated stainless steel
•Full one year limited warranty against defects in materials and workmanship
For safer and easier trolling and boating. E.Z. Steer has a kit to fit
every outboard and outdrive engine, even if you have a swim platform. The
rod comes ready to install in six standard lengths, ranging from 19 to
60 inches. To find the proper compressed length your boat requires, measure
from the center of your auxiliary to the center of your main engine with
both engines down and straight ahead. Remember, when mounting on a full
or 3/4 swim platform, a special bracket and long rod are required. Custom
length rods are available on a special order basis. Short Rod kits are
generally needed when the auxiliary is transom mounted and standard kits
are used when the auxiliary is mounted on a lift bracket. Seadrives or extended bracket outboards
usually require a Long, Ultra, Extra Long or Custom rod.
Each full kit consists of:
•Main bracket assembly
•Small outboard bracket assembly
•All necessary hardware
•One of the following self-adjusting rods:
Short Rod 19"-22", Standard Rod 23"-26", Medium Rod
27"-28", Long Rod 29"-33", Ultra Rod 34"-38",
Extra Long Rod 39"-46". Custom Length Rods Also Available.
Rod Assemblies:
- EZSEZ-10001 Short rod assembly complete 19" to 22"
- EZSEZ-10002 Standard rod assembly complete 23" to 26"
- EZSEZ-10003 Long rod assembly complete 29" to 33"
- EZSEZ-10004 Medium rod assembly complete 27" to 28"
- EZSEZ-10005 Extra Long assembly 39" to 46"
- EZSEZ-10006 ULTRA rod assembly - 34" to 38"
Complete Kits:
- EZSEZ-20002 OMC standard kit
- EZSEZ-22002 OMC Cobra standard kit
- EZSEZ-30002 Mercury Alpha I standard kit
- EZSEZ-37002 Mercury Alph 1/2G standard kit
- EZSEZ-40002 Volvo I standard kit
- EZSEZ-42002 Volvo II standard kit
- EZSEZ-60001 Short outboard to outboard kit
- EZSEZ-60002 Standard outboard to outboard kit
Click for Prices/Order
Top
For Single or Twin V4 and V6 engines
Featuring the new and revolutionary K-6 cylinder with its slim line
profile and universal base-mount design. Neatly mounts to all V4 and V6
engines without using the tilt tube!
Easily installs on: Mercury/Mariner - Evinrude & Johnson - Suzuki
- Yamaha
Also Featuring The New "Glide-Free" 80 Series Helm. Eliminates
Torque Feedback From Big Outboards So Every Member of the Family Can Enjoy
Smooth, Effortless, Steering.
Extremely simple to install. System includes all necessary hardware
and 50 feet of hose with attached helm fittings so you can custom cut the
hose at the cylinder end to the exact length you need.
Ultra sleek cylinder design requires less space around the engine and
improves the appearance of your boat.
Accepts port or starboard hose connections.
Helm mounts in front of or behind the dash and is powder coated for
extra corrosion resistance and longer life.
Stainless steel helm shaft.
Unique no-mess purge kit. Bypass tube easily connects to cyinder, fill-tube
connects to helm, then just rotate wheel to purge.
Yes...it really is that simple! The ultimate in Compact Hydraulic Steering
Systems. Everything You Need, Packaged in a Single Box.
OB800-11H Outboard Hydraulic Steering Package Includes:
•H-820, Hytrac 2.0 Helm
•K-6, Hy-Trac Universal Base-Mount Cylinder
•All Mounting Hardware fo Helm & Cylinder
•50 feet Marine Steering Hose
•Hose Fittings Kit
•1/2 Gallon of Hydraulic Fluid
•Complete Purging Kit
•Installation and Owner's Manual
Dual Stations Order 1) H-820 Helm 1) HF42 Station Fittings, plus MSHS
Hose and fittings as needed.
|
